Korg Krome - 019: St. Analog Record (Stereo Analog Record)

262
a: Pre LPF
If a sampler with a very low sampling frequency receives
very high‐pitched sound that could not be heard during
playback, it could generate pitch noise that is unrelated to
the original sound. Set Pre LPF to On to prevent this noise
from being generated.
If you set the Sampling Frequency to about 3 kHz and set
Pre LPF to Off, you can create a sound like a ring modulator.
g: Resolution
h: Output Level
If you set a smaller value for the Resolution parameter, the
sound may be distorted. The volume level may also be
changed. Use Output Level to adjust the level.
019: St. Analog Record (Stereo
Analog Record)
This effect simulates the noise caused by scratches and dust
on analog records. It also reproduces some of the
modulation caused by a warped turntable.
b: Flutter
This parameter enables you to set the depth of the
modulation caused by a warped turntable.
e: Click Level
This parameter enables you to set the level of the click noise
that occurs once every rotation of the turntable. This
simulation reproduces record noise, and the noise generated
after the music on a vinyl record finishes.
e
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
f
Depth 0...100
Sets the depth of the sampling
frequency LFO modulation
Src Off...Tempo
Selects the LFO modulation
source of the sampling
frequency
Amt –100...+100
Sets the LFO modulation
amount of the sampling
frequency
g Resolution 4...24 Sets the data bit length p.262
h
Output Level 0...100 Sets the output level p.262
Src Off...Tempo
Selects the modulation source
for the output level
Amt –100...+100
Sets the modulation amount of
the output level
i
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
a Speed [RPM] 33 1/3, 45, 78 Sets the r.p.m. of a record
b Flutter 0...100
Sets the modulation depth
p.262
c
Noise Density 0...100 Sets the noise density
Noise Tone 0...100 Sets the noise tone
d
Noise Level 0...100 Sets the noise level
Src Off...Tempo
Selects the modulation source
for the noise level
Amt –100...+100
Sets the modulation amount of
the noise level
e
Click Level 0...100
Sets the click noise level
p.262
Src Off...Tempo
Selects the modulation source
for the click noise level
Amt –100...+100
Sets the modulation amount of
the click noise level
f EQ Trim 0...100 Sets the EQ input level
g
Pre EQ Cutoff
[Hz]
300...10.00k Sets the EQ center frequency
Q 0.5...10.0 Sets the EQ band width
Gain [dB] –18.0...+18.0 Sets the EQ gain
h
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Analog Record
Simulation
Pre EQ
Pre EQ
EQ Trim
EQ Trim