Global mode
206
5–1: Sample Setup
Here, you can select a drum kit and specify Drumsample 1–
8 as the drum samples assigned to each key. Here, you can
also edit drum sample parameters for each Drumsample.
5–1a: Drum Kit, Key Select, Assign
Drum Kit Select [00(INT)...47(USER)]
Selects the drum kit that you wish to edit.
KEY [C–1...G9]
Selects the key to which the drum sample (and its settings)
will be assigned.
If you check Assign for the key you select here, the
Drumsample 1–8, Voice Assign Mode, and Mixer
parameters (see below) will be used.
Assign [Off, On]
On (checked): The drum samples you assigned for
Drumsample 1–8 will sound. Normally you will check this
parameter.
Off (unchecked): The selected drum samples will be
invalid, and the drum samples of the key to the right will
sound. At this time, the pitch will be a semitone lower than
the pitch of the key to the right. Uncheck this parameter
when you wish to play a drum sample at differing pitches.
5–1b: Drumsample
You can specify up to eight drum samples.
By dragging the slider at the left, you can select the velocity
zone to be edited. You can also make this selection by
directly pressing the desired zone.
1: (Drumsample1)
These are the settings for the first (High) velocity zone.
If you want to create a simple setup using only one drum
sample, make the appropriate settings in Drumsample 1,
and then set Threshold Velocity to 1 and Xfd to Off.
Drumsample 1 On/Off [Off, On]
On (checked): Check this if you want to use Drumsample 1.
The selected drum sample will sound.
Off (unchecked): Drumsample 1 will not be used. The drum
sample will not sound.
Note: Normally, you will start by using Drumsample 1
(before using Drumsample 1–8). If you don’t want to switch
drum samples by velocity, turn on only Drumsample 1. If
you’re using multiple velocity‐switched drum samples,
make settings as follows.
One velocity zone
Drumsample 1: On, Drumsample 2–8: Off
Two velocity zones
Drumsample 1, 2: On, Drumsample 3–8: Off
Eight velocity zones
Drumsample 1–8: On
Bank [Mono, Stereo, XL.M, XL.St]
Drumsample Select
[List of installed Drumsample]
Specify the Drumsample 1 drum sample by bank and drum
sample number.
Bank selects either Mono or Stereo drum samples. However,
stereo drum samples will use twice as many voices as mono
drumsamples.
Mono, Stereo: Conventional monaural or stereo drum
samples.
XL.M (eXtra Large Mono), XL.St (eXtra Large Stereo):
High‐capacity monaural or stereo drum samples.
When you press the Drumsample Select popup button a
drum sample list will appear, allowing you to choose drum
samples from the list.
Use the tabs to choose a category, and then choose a drum
sample from within the category. Press the OK button to
execute, or press the Cancel button to cancel.
It is not possible to edit the category names of drum
samples, or to re‐assign the category.
If you choose “Bank” Mono:
Mono drum samples will be displayed. The L‐channel or R‐
channel of the stereo drum samples selectable via Bank:
Stereo can also be selected as mono drum samples. In these
cases, –L or –R is shown following the drum sample of the
same name.
If you choose “Bank” Stereo:
Only stereo drum samples will be displayed.
Rev (Reverse) [Off, On]
This lets you play the selected drum sample backwards,
without looping. However, some preset drum samples
cannot be reverse‐played, and consequently, they cannot be
selected.
On (checked): The drum sample will play back in reverse.
No. (Bank) Contents
00(INT)...31(INT) KROME preloaded drum kits
32(USER)...47(USER) User drum kits
5–1a
5–1b
5–1
Menu
Velocity Split
Drum Kit, Key Select, Assign
C4 key
Drum Kit
KEY Assign
KEY: The selected key is shown in blue.
You can select a key by holding down the ENTER switch and playing
the desired note.
To Next Page
Loading...
