SEQ P0: Play/REC 0–3: Mixer T01–08, 0–4: Mixer T09–16
113
0–3: Mixer T01–08,
0–4: Mixer T09–16
Here, you can set the pan and volume of each MIDI track.
0–3(4)a:Location, Meter, Tempo, Tempo
Mode, Song Select, Track Select,
Reso, RPPR
For more information, please see “0–1: Program T01–08, 0–2:
Program T09–16” on page 109.
0–3(4)b: Pan, Volume
The pan and volume that you specify here will be used
when you play back or record from the beginning of the
song. If you change the settings during recording, the
changes will be recorded as MIDI data, and pan and volume
will change during playback. You can also change the
settings during playback. However, when the song reaches a
location where pan or volume data was recorded, the
settings will change accordingly.
Selected Track Info
This area shows information on the MIDI track selected for
editing.
For more information, please see “0–1(2)b: Track Program
Select” on page 111.
Track 01 (Track Number):
Category [Category Name]
This indicates the category.
Pan [RND, L001...C064...R127]
Here, you can set the pan of each MIDI track.
L001…C064…R127: A setting of L001 is far left and R127 is
far right. A setting of C064 will reproduce the oscillator pan
setting of the Program mode.
If a mono insert effect is in use, the settings you make here
will be ignored. In this case, the Pan: #8 parameter in P8:
Routing/IFX– Insert FX Setup page will adjust the panning
of the sound after the Insert Effect. For more information,
please see “Mixer” on page 243.
RND: The pan position will change randomly at each note‐
on.
If Status (Seq 3–1(2)c) is INT or BTH, CC#10 Pan can be
received to control the panning. When receiving CC#10,
a value of 0 or 1 is far left, 64 is center, and 127 is far
right. When you change the song or return to the
beginning of the song, tracks whose Status is EXT, EX2
or BTH will transmit the pan you specify here as a MIDI
message (except for RND). (See Global P1: MIDI, SEQ
Mode “Track MIDI Out” on page 200)
Volume [000...127]
Here, you can set the volume of each MIDI track.
When Status (Seq 3–1(2)c) is INT or BTH, CC#7 Volume
can be received to control the volume. The volume of a
track is determined by multiplying the MIDI Volume
(CC#7) and Expression (CC#11) values. When you
change the song or return to the beginning of the song,
tracks whose Status is EXT, EX2 or BTH will transmit
the volume you specify here as a MIDI Volume
message. (See Global P1: MIDI, SEQ Mode “Track MIDI
Out” on page 200)
Track 02...08, 09...16 (Track Number):
For more information, please see “Track 01 (Track
Number):” above.
V
0–3(4): Menu Command
•0: Memory Status see p. 163
•1: Exclusive Solo see p. 64
•2: Rename Song see p. 163
•3: Delete Song see p. 163
•4: Copy From Song see p. 163
•5: Load Template Song see p. 163
•6: Save Template Song (Save as User Template Song)
see p. 164
•7: FF/REW Speed see p. 164
•8: Set Location (Set Location for Locate Key) see p. 164
•9: GM Initialize see p. 165
•10:
Copy from Combination
see p. 166
•11: Copy from Program see p. 167
For more information, please see “Sequencer: Menu
Command” on page 163.
Selected Track Info
Track Number
Track Category
OSC1:
Amp1 Pan=L001
OSC2:
Amp2 Pan=R127
Left
Center
Right
Pan (CC#10)
C064
Left
Center
Right
L032
L001
R096
R127
Left
Center
Right
Left
Center
Right
OSC1
OSC2
OSC1
OSC2
OSC1:
Amp1 Pan=L032
OSC2:
Amp2 Pan=R096
Pan (CC#10)
C064
L032
L001
R096
R127
OSC1:
Amp1 Pan=C064
OSC2:
Amp2 Pan=C064
Left
Center
Right
Pan (CC#10)
C064
Left
Center
Right
L032
L001
R096
R127
OSC1
OSC2
To Next Page
Loading...
