Program mode
62
menu, and then choose an effect within that category. Press
the OK button to execute your choice, or press the Cancel
button to cancel.
TFX On/Off [Off, On]
This turns total effect on/off. If this is off, the input will be
passed directly through. The setting will alternate between
on/off each time you press this.
Tip: An easy way to disable the total effect is to turn off the
front panel TOTAL FX button. TFX will be temporarily
disabled, and will stay off even if you switch programs or
modes. When you turn the switch on, the total effect will be
enabled, and you will obtain the effect specified by the
program or combination.
Note: The TOTAL FX button is linked with Global P0‐1
Effect Global SW Enable TFX (see p.5).
Alternatively, you can send control change #95 to turn
the total effect off. A value of 0 turns the total effect off,
and values of 1–127 restore the original setting. The
global MIDI channel specified by MIDI Channel
(Global 1–1a) is used for this message.
9–1c: Master Volume
Master Volume [000...127]
This specifies the final level of the audio output that has
passed through total effect, and output from AUDIO
OUTPUT L/MONO and R.
V
9–1: Menu Command
•0: Write Program see p. 64
•1: Exclusive Solo see p. 64
•2: Auto Song Setup see p. 65
•3: Copy MFX/TFX see p. 67
•4: Swap MFX/TFX see p. 67
•5: Write FX Preset see p. 67
For more information, please see “Program: Menu
Command” on page 64.
9–2: MFX1
9–2a: MFX1
Here you can edit the parameters of the effect you choose for
MFX1 in the P9: MFX/TFX/LFO– Routing page.
Effect dynamic modulation (Dmod) is controlled on the
global MIDI Channel (Global 1–1a). For more
information, please see “Dynamic Modulation Source
List” on page 346.
MFX1 On/Off [Off, On]
This turns master effect 1 on/off. It is linked with the on/off
setting in the P9: MFX/TFX/LFO– Routing page.
The setting will alternate between On and Off each time you
press this.
Alternatively, you can use CC#94 to turn Master effects
1/2 off. CC#95 will turn the Total effect off. A value of 0
is Off, and a value of 1–127 selects the original setting.
This is controlled on the global MIDI channel specified
by MIDI Channel (Global 1–1a).
P (Effect Preset)
[P00, P01...15, U00...15, ---------------]
This selects the effect preset. For more information, please
see “P (Effect Preset)” on page 60.
MFX1 Parameters
Here, you can edit the parameters of the master effect
selected in the P9: MFX/TFX/LFO– Routing page.
For details on the master effects, please see “Master Effects
(MFX1, 2)” on page 245.
V
9–2: Menu Command
•0: Write Program see p. 64
•1: Exclusive Solo see p. 64
•2: Auto Song Setup see p. 65
•3: Copy MFX/TFX see p. 67
•4: Swap MFX/TFX see p. 67
•5: Write FX Preset see p. 67
For more information, please see “Program: Menu
Command” on page 64.
9–3: MFX2, 9–4: TFX
These pages let you edit the parameters of Master Effect 2
and Total Effect. To select different effects types, use the P9:
MFX/TFX/LFO– Routing page.
The parameters for MFX2, TFX is the same as for MFX1. For
more information, please see “9–2: MFX1” on page 62.
To Next Page
Loading...
