Korg Krome - 182: EP Cabinet;Drive; 183: St. MIC + Preamp; Preamp); 184: Multitap Cho;Delay (Multitap Chorus;Delay)

Double Size 182: EP Cabinet/Drive
331
182: EP Cabinet/Drive
This faithfully simulates the characteristics of the power
amp and speaker cabinet of a famous model of tine‐type
electric piano. It produces a tone with a distinctive sense of
drive and warmth.
c: Drive
At lower settings, the amp is very clean; as you increase the
Drive, it gets dirtier and more distorted. The output level is
compensated, so increasing Drive causes only a moderate
increase in perceived volume.
183: St. Mic + PreAmp (Stereo
Mic Modeling + PreAmp)
This is a stereo mic and preamp simulator (See “028: Mic
Model+PreAmp (Mic Modeling + PreAmp)” on page 267.).
For example you might use this to simulate micing of a
stereo source such as a rotary speaker.
184: Multitap Cho/Delay
(Multitap Chorus/Delay)
This effect has six chorus blocks with different LFO phases.
You can produce a complex stereo image by setting a
different delay time and depth for each block. You can
control the delay output level via a modulation source.
a Cabinet Type
Tine EP I,
Tine EP II,
Reed EP
Select the power amp and
speaker cabinet.
b
Drive Switch Off, On Switches drive on/off
Src Off...Tempo
Selects a modulation source to
switch drive on/off
Sw
Toggle,
Moment
Sets the switch mode for drive
on/off modulation
c
Drive 00.0…100
Sets the amount of overdrive
and distortion in the amp
Src Off...Tempo
Selects a modulation source for
Drive
Amt –100...+100
Sets the modulation amount for
Drive
d
Wet/Dry
Dry,
1 : 99...99 : 1,
Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Tube Pre AmpMic Simulation
Tube Pre AmpMic Simulation
Left
Right
Wet / Dry
Output Level
Wet / Dry
Stereo In - Stereo Out
a
LFO
Frequency
[Hz]
0.02...13.00 Sets the speed of the LFO
b
Tap1 (000)
[msec]
0...2000
Sets the Tap1 (LFO phase=0
degrees) delay time
Depth 0...30 Sets the Tap1 chorus depth
Status
Always On,
Always Off,
OnOff
(Dm),
OffOn
(Dm)
Selects on, off, or modulation
source for the control of Tap1
output
p.332
c
Tap2 (180)
[msec]
0...2000
Sets the Tap2 (LFO phase=180
degrees) delay time
Depth 0...30 Sets the Tap2 chorus depth
Status
Always On,
Always Off,
On  Off (Dm),
Off
 On (Dm)
Selects on, off, or modulation
source for the control of Tap2
output
p.332
d
Tap3 (060)
[msec]
0...2000
Sets the Tap3 (LFO phase=60
degrees) delay time
Depth 0...30 Sets the Tap3 chorus depth
Status
Always On,
Always Off,
OnOff
(Dm),
OffOn
(Dm)
Selects on, off, or modulation
source for the control of Tap3
output
p.332
e
Tap4 (240)
[msec]
0...2000
Sets the Tap4 (LFO phase=240
degrees) delay time
Depth 0...30 Sets the Tap4 chorus depth
Status
Always On,
Always Off,
OnOff
(Dm),
OffOn
(Dm)
Selects on, off, or modulation
source for the control of Tap4
output
p.332
f
Tap5 (120)
[msec]
0...2000
Sets the Tap5 (LFO phase=120
degrees) delay time
Depth 0...30 Sets the Tap5 chorus depth
Status
Always On,
Always Off,
OnOff
(Dm),
OffOn
(Dm)
Selects on, off, or modulation
source for the control of Tap5
output
p.332
g
Tap6 (300)
[msec]
0...2000
Sets the Tap1 (LFO phase=300
degrees) delay time
Depth 0...30 Sets the Tap6 chorus depth
Status
Always On,
Always Off,
OnOff
(Dm),
OffOn
(Dm)
Selects on, off, or modulation
source for the control of Tap6
output
p.332
Left
Right
Feedback
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
LFO: Triangle
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap5 Delay
Tap6 Delay
Tap4 Delay
D
-mod
On/O Control
Panning Preset