Chorus, Flanger, and Phaser (Cho/Fln Phaser) 041: St. Env. Flanger (Stereo Envelope Flanger)
273
041: St. Env. Flanger (Stereo
Envelope Flanger)
This Flanger uses an envelope generator for modulation. You will
obtain the same pattern of flanging each time you play. You can
also control the Flanger directly using the modulation source.
c: Sweep Mode
c: Src
This parameter switches the flanger control mode. With
Sweep
Mode
= EG, the flanger will sweep using the envelope
generator. This envelope generator is included in the envelope
flanger, and not related to the Pitch EG, Filter EG, or Amp EG.
The Src parameter selects the source that starts the envelope
generator. If you select, for example, Gate, the envelope
generator will start when the note‐on message is received.
When Sweep Mode = D‐mod, the modulation source can
control the flanger directly. Select the modulation source
using the Src parameter.
The effect is off when a value for the modulation source
specified for the Src parameter is smaller than 64, and
the effect is on when the value is 64 or higher. The
Envelope Generator is triggered when the value
changes from 63 or smaller to 64 or higher.
d: EG Attack
d: EG Decay
Attack and Decay speed are the only adjustable parameters on
this EG.
042: Stereo Phaser
This effect creates a swell by shifting the phase. It is very
effective on electric piano sounds. You can add spread to the
sound by offsetting the phase of the left and right LFOs from
each other.
h: Resonance
i: Wet/Dry
The peak shape of the positive and negative Feedback value
is different. The harmonics will be emphasized when the
effect sound is mixed with the dry sound, if you set a
a
L Delay
Bottom
[msec]
0.0...50.0
Sets the lower limit of the left-
channel delay time
L Delay Top
[msec]
0.0...50.0
Sets the upper limit of the left-
channel delay time
b
R Delay
Bottom
[msec]
0.0...50.0
Sets the lower limit of the right-
channel delay time
R Delay Top
[msec]
0.0...50.0
Sets the upper limit of the right-
channel delay time
c
Sweep Mode EG, D-mod
Determines whether the flanger
is controlled by the envelope
generator or by the modulation
source p.273
Src Off...Tempo
Selects the modulation source
that triggers the EG (when
Sweep Mode = EG), or the
modulation source that causes
the flanger to sweep (when
Sweep Mode = D-mod) p.273
d
EG Attack 1...100 Sets the EG attack speed p.273
EG Decay 1...100 Sets the EG decay speed p.273
e Feedback –100...+100
Sets the feedback amount
p.272
f
High Damp
[%]
0...100
Sets the feedback damping
amount in the high range
p.272
g
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.259, p.272
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
EG Attack/Decay
EG
D-mod
Sweep Mode
D
-mod
Flanger
Flanger
Left
Right
Feedback
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
a
LFO
Waveform
Triangle, Sine Selects the LFO Waveform
LFO Shape –100...+100
Changes the curvature of the
LFO Waveform p.258
b
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
p.259
c
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO p.257
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
d
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
e
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
f
Manual 0...100
Sets the frequency to which the
effect is applied
Src Off...Tempo
Selects the modulation source
for the LFO modulation
Amt –100...+100
Sets the modulation amount of
the LFO modulation
j
Depth 0...100
Sets the depth of LFO
modulation
Src Off...Tempo
Selects the modulation source
for the LFO modulation depth
Amt –100...+100
Sets the modulation amount of
the LFO modulation depth
h
Resonance –100...+100
Sets the resonance amount
p.273
High Damp
[%]
0...100
Sets the resonance damping
amount in the high range
p.274
i
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.259, p.273
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt
–
100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Resonance
LFO Shape
LFO Phase
LFO: Tri / Sine
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Phaser
Phaser
To Next Page
Loading...
