278
051: 2Voice Resonator
This effect resonates the input signal at a specified pitch.
You can set the pitch, output level, and pan settings for two
resonators individually. You can control the resonance
intensity via an LFO.
a: Control Mode
g: Voice 1: Resonance
i: Voice 2: Resonance
This parameter determines the resonance intensity.
When Control Mode = Manual, the Resonance parameter
sets the intensity of resonance. If the Resonance parameter
has a negative value, harmonics will be changed, and
resonance will occur at a pitch one octave lower.
When Control Mode = LFO, the intensity of resonance
varies according to the LFO. The LFO sways between
positive and negative values, causing resonance to occur
between specified pitches an octave apart in turn.
When Control Mode = D‐mod, the resonance is controlled
by the dynamic modulation source. If JS X is assigned as the
modulation source, the pitch an octave higher and lower can
be controlled, similar to when LFO is selected for Control
Mode.
a: LFO/D-mod Invert
When Control Mode = LFO or D‐mod, the controlled phase
of either Voice 1 or 2 will be reversed. When the resonance
pitch is set for Voice 1 (Resonance has a positive value),
Voice 2 will resonate at a pitch an octave below (Resonance
has a negative value).
f: Voice 1: Pitch
f: Fine [cent]
h: Voice 2: Pitch
h: Fine [cent]
The Pitch parameter specifies the pitch of resonance by note
name. The Fine parameter allows for fine adjustment in
steps of cents.
d
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
p.259
e
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for
LFO speed
Amt
–20.00...
+20.00
Sets the modulation amount of
LFO speed
f
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
g
L Delay Time
[msec]
0.0...500.0 Sets the left channel delay time
R Delay Time
[msec]
0.0...500.0 Sets the right channel delay time
h Depth 0...200
Sets the depth of LFO
modulation
i
Feedback –100...+100
Sets the feedback amount
p.272
High Damp
[%]
0...100
Sets the feedback damping
amount in the high range
p.272
j
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the balance between the
effect and the dry input
p.259, p.272
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
a
Control
Mode
Manual, LFO,
D-mod
Switches the controls of
resonance intensity p.278
LFO/D-mod
Invert
Off, On
Reverses the Voice 1 and 2
control when LFO/D-mod is
selected p.278
b
LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
D-mod Src Off...Tempo
Selects the modulation source
that controls resonance intensity
c
MIDI Sync Off, On
When this is on, the LFO speed is
set by BPM, Base Note, and
Times, instead of Frequency
p.257
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo;
40–300 sets the tempo manually
fo
r
this individual effect p.257
Base Note ...
Selects the type of notes that
specify the LFO speed p.257
Times x1...x32
Sets the number of notes that
specify the LFO speed p.257
Left
Right
Resonance
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
High Damp
High Damp
Trim
Trim
+
Level
Level
Pan
Pan
Control Mode
D
-mod
LFO
Manual
Invert: On/O
Resonator
Resonator
Pitch, Fine [cents]
d
LFO Type
Individual,
Common1,
Common2
Selects either (individual) LFO,
Common FX LFO1, or Common
LFO2 p.257
Common
LFO Offset
[deg]
–180...+180
Sets the phase offset when Type
= Common 1 or Common 2
p.257
e
Mod. Depth –100...+100
Sets the amount of resonance
intensity control via LFO/D-mod
Trim 0...100
Sets the input level at the
resonator
f
Voice1: Pitch C0...B8
Sets the voice1 Pitch for
resonance p.278
Fine [cent] –50...+50
Fine-adjusts the voice 1 pitch for
resonance p.278
Level 0...100 Sets the Voice1 output level
g
Voice1:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
p.278
High Damp
[%]
0...100
Sets the damping amount of
resonant sound in the high
range p.279
Pan
L6...L1, C,
R1...R6
Sets the Voice1 stereo image
h
Voice2: Pitch C0...B8
Sets the voice 2 Pitch for
resonance p.278
Fine [cent] –50...+50
Fine-adjusts the voice 2 pitch for
resonance p.278
Level 0...100 Sets the Voice2 output level
i
Voice2:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
p.278
High Damp
[%]
0...100
Sets the damping amount of
resonant sound in the high
range p.279
Pan
L6...L1, C,
R1...R6
Sets the Voice2 stereo image
j
Wet/Dry
Dry, 1 :99... 99
: 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
To Next Page
Loading...
