Korg Krome - 109: Limiter - Phaser; 110: Limiter - Mt.delay (Limiter - Multitap Delay)

308
109: Limiter - Phaser
This effect combines a mono limiter and a phaser. You can
change the order of the effects.
110: Limiter - Mt.Delay
(Limiter - Multitap Delay)
This effect combines a mono limiter and a multitap delay.
You can change the order of the effects.
i
[F]Output
Mode
Normal,
Wet Invert
Selects the output mode for the
chorus/flanger p.305
Routing
Limiter
Flanger,
Flanger
Limiter
Switches the order of the limiter
and chorus/flanger
j
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
LIMITER
a
[L]Ratio
1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal compression ratio
p.307
Threshold
[dB]
–40...0
Sets the level above which the
compressor is applied p.307
b
[L]Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
c
[L]Gain
Adjust [dB]
–Inf,
–38...+24
Sets the limiter output gain
p.307
PHASER
d
[P]LFO
Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
LFO
Waveform
Triangle, Sine Selects the LFO Waveform
e
[P]Manual 0...100
Sets the frequency to which the
effect is applied
Depth 0...100
Sets the depth of LFO
modulation
Resonance –100...+100
Sets the resonance amount
p.273
f
[P]Phaser
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the phaser effect balance
p.259, p.273
Src Off...Tempo
Selects the phaser’s Wet/Dry
modulation source
Amt –100...+100
Sets the phaser’s Wet/Dry
modulation amount
g
[P]Output
Mode
Normal,
Wet Invert
Selects the phaser output mode
p.302
h Routing
Limiter
Phaser,
Phaser
Limiter
Switches the order of the limiter
and p
h
aser p.305
i
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Limiter
Limiter
Gain Adjust
Envelope - Control
Phaser
Phaser
Resonance
LFO: Tri / Sine
Phaser Wet / Dry
Normal
Wet Invert
Output Mode
–
+
LIMITER
a
[L]Ratio
1.0 : 1...
50.0 : 1, Inf : 1
Sets the signal compression ratio
p.307
Threshold
[dB]
–40...0
Sets the level above which the
compressor is applied p.307
b
[L]Attack 1...100 Sets the attack time
Release 1...100 Sets the release time
c
[L]Gain
Adjust [dB]
–Inf,
–38...+24
Sets the limiter output gain
p.307
MULTITAP DELAY
d
[D]Tap1 Time
[msec]
0.0...1360.0 Sets the Tap1 delay time
Tap1 Level 0...100 Sets the Tap1 output level p.290
e
[D]Tap2 Time
[msec]
0.0...1360.0 Sets the Tap2 delay time
Feedback –100...+100 Sets the Tap2 feedback amount
f
[D]High
Damp [%]
0...100
Sets the damping amount in the
high range p.289
g
[D]Mt.Delay
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the multitap delay effect
balance
Src Off...Tempo
Selects the multitap delay’s Wet/
Dry modulation source
Amt –100...+100
Sets the multitap delay’s Wet/Dry
modulation amount
h Routing
Limiter
Mt.Delay,
Mt.Delay
Limiter
Switches the order of the limiter
and multitap delay
i
Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance between the
effect and the dry input
Src Off...Tempo
Selects a modulation source for
Wet/Dry
Amt –100...+100
Sets the modulation amount for
Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly Wet / Dry
Limiter
Limiter
Gain Adjust
Envelope - Control