Global P1: MIDI 1–2: MIDI Routing
201
In Combination mode (P0: Play), the combination will be
switched when a program change message is received on
the global MIDI channel. However, it is possible to set the
Enable Combination Change parameter so that the
combination is not switched. When a program change is
received on the channel specified for each timbre by MIDI
Channel (Combi 3–1(2)c), the program of that timbre will be
switched. However, the program changes for each timbre
will be affected by the setting of the Enable Program
Change parameter (Combi 5–1(2)c).
When you switch combinations, a program change message
will be transmitted on the global MIDI channel, and also
transmitted simultaneously on the channel of timbres whose
Status (Combi 3–1(2)c) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on
a channel that corresponds to a track whose Status (Seq 3–
1(2)c) is set to INT or BTH will switch programs on that
track.
When you select a song or play back sequencer data,
program changes will be transmitted on the channels of
tracks whose Status is set to BTH, EXT, or EX2.
Off (unchecked): Program changes will not be transmitted
or received.
Bank Change [Off, On]
On (checked): The Bank Select control change message will
be transmitted together with program change messages.
This is valid when Enable Program Change is checked.
Off (unchecked): Bank Select messages will not be
transmitted or received.
When recording on the internal sequencer, bank select
messages will be recorded regardless of this setting.
However for playback, this setting will apply.
Combination Change [Off, On]
On (checked): When in Combi P0: Play, an incoming
program change message on the global MIDI channel set by
MIDI Channel (Global 1–1a) will switch combinations.
This is valid when Enable Program Change is checked.
An incoming program change on a channel other than the
global MIDI channel will switch the program of any timbre
that matches that MIDI channel.
Off (unchecked): An incoming program change message on
the global MIDI channel will switch the program of any
timbre whose MIDI Channel (Combi 3–1(2)c) matches the
global MIDI channel. The combination will not be switched.
The program changes for each timbre will be affected by the
setting of the Enable Program Change parameter (Combi 5–
1(2)c).
Enable After Touch [Off, On]
On (checked): MIDI aftertouch messages will be transmitted
and received.
Off (unchecked): MIDI aftertouch messages will neither be
transmitted nor received.
This setting has no effect when you use the internal
sequencer to playback sequence data that was recorded with
aftertouch data; i.e., aftertouch will be transmitted via MIDI.
Performing on the KROME’s keyboard will transmit neither
channel aftertouch nor polyphonic aftertouch. However,
since the KROME does support aftertouch as an Alternate
Modulation Source (AMS), it can receive aftertouch to
control.
Enable Control Change [Off, On]
On (checked): Control change messages will be transmitted
and received.
Off (unchecked): Control change messages will neither be
transmitted nor received.
This setting has no effect when you use the internal
sequencer to play back sequence data that was recorded
with control change data; i.e., the control changes
previously recorded into the sequencer will be transmitted
via MIDI.
Enable Exclusive [Off, On]
On (checked): System Exclusive data will be transmitted
and received.
Check this if you want to edit the KROME from a connected
computer, or if you want to allow bi‐directional editing.
Off (unchecked): System Exclusive data will not be
transmitted. Normally you will leave this unchecked.
However, System Exclusive data will be transmitted and
received while the menu commands (Dump Program–
Dump Drum Track Pattern) of this page are displayed.
V
1–2: Menu Command
•0: Write Global Setting see p. 216
•1: Dump Program see p. 218
•2: Dump Combination see p. 218
•3: Dump Drum Kit see p. 218
•4: Dump Arpeggio Pattern see p. 218
•5: Dump Global Setting see p. 218
•6: Dump Sequencer see p. 218
•7: Dump Drum Track Pattern see p. 218
For more information, please see “Global: Menu Command”
on page 216.
To Next Page
Loading...
