Korg Krome - Page 365

KROME and MIDI CCs
357
You can assign any control change number (CC#00–119) to
the Realtime Controls Knobs USER 1–4. In this case, the
transmitted values will all be 0…127.
You can assign any control change number (CC#00–119) to
the ARP button, arpeggio control knobs 1–4. In this case,
ARP buttons will transmit values of 0 (Off) or 127 (On),
knobs 1–4 will transmit values of 0…127.
*1 In the KROME sequencer, bank select messages are
normally specified as program change events (“MIDI
Event Edit” Sequencer P6). However in some cases this
will be insufficient when you wish to change banks on an
external device. In such cases, you can use CC#00 and
CC#32 to specify the banks.
For information on the relation between bank select
numbers and the banks of your external device, refer to
the owner’s manual for your external device.
*2 Unlike conventional control changes, pitch bend range,
fine tune, and coarse tune settings are made using RPC
(Registered Parameter Control) messages. In Program,
Combination, and Sequencer modes, you can use RPC
messages to control the bend range and tuning for each
program, Timbre (Combination), or Track (Sequencer).
The procedure is to use an RPN (Registered Parameter
Number) message to select the parameter that you wish
to edit, and then use Data Entry to input a value for that
parameter. To select the parameter, use CC#100 (with a
value of 00…02) and CC#101 (with a value of 00). use
CC#06 and CC#38 to enter the data.
The data entry values for each parameter and the corre‐
sponding settings are as follows.
For example, if in Sequencer mode you wish to set a
MIDI track that is receiving channel 1 to a transpose
(coarse tuning) value of –12, you would first transmit [B0,
64, 02] (64H=CC#100) and [B0, 65, 00] (65H=CC#101) to
the KROME to select the RPN coarse tune. Then you
77 LFO1 depth 0…127 pitch LFO1 intensity *4
78 LFO1 delay 0…127 LFO1 delay *4
79 Filter EG intensity 0…127 filter EG intensity *4
80 SW1 modulation On/Off
0…63(Off),
64…127(On)
corresponds to on/off when the SW1 function is set to SW1 Mod.
81 SW2 modulation On/Off
0…63(Off),
64…127(On)
corresponds to on/off when the SW2 function is set to SW2 Mod.
82 Foot switch On/Off
0…63(Off),
64…127(On)
corresponds to on/off when the function of the assignable foot switch is set
to Foot SW
83 Controller (CC#83) 0…127 for controlling AMS or Dmod
84 – – –
85…88 Controller (CC#85…88) 0…127 for controlling AMS or Dmod
89, 90 – – –
91 Effect depth 1 (send 2 level) 0…127 send 2 level
92
Effect depth 2 (Insert Effect 1–5 On/
Off)
0…63(Off),
64…127(On)
turn Insert effect 1…5 on/off *5
93 Effect depth 3 (send 1 level) 0…127 send 1 level
94
Effect depth 4 (master effect 1, 2
On/Off)
0…63(Off),
64…127(On)
master effect 1, 2 on/off *5
95 Effect depth 5 (total effect On/Off)
0…63(Off),
64…127(On)
total effect on/off *5
96 Data increment 0
97 Data decrement 0
98 NRPN(LSB) – LSB of NRPN
99 NRPN(MSB) – MSB of NRPN
100 RPN(LSB)
0 selects the pitch bend range *2
1 controls Fine Tune *2
2 controls Coarse Tune *2
101 RPN(MSB) 0 MSB of RPN
102...119 – – –
CC# Control Value Function
CC#06 CC#38
RPN=1 (Fine tune)
Parameter value (1 cent steps)
CC#06 CC#38
RPN=2 (Coarse tune)
Parameter value (Semitone steps)
CC#06 CC#38
RPN=0 (Pitch bend range)
Parameter value (Semitone steps)
0
12
24
127
00
00
00
00
0
+12
+24
+24
0
64
127
127
00
00
00
127
-100
0
+98
+99
0
40
64
88
127
00
00
00
00
00
-24
-24
0
+24
+24