MIMAKI UJF-3042 - Page 208

© 2013 MIMAKI ENGINEERING CO.,LTD.
7.1.2 P.7
7.1.2 List of Error Messages
1
2
3
4
5
6
7
8
47
ERROR60c
INK TYPE
Type of inserted Ink Cartridge is different. 1. Check the type of the ink cartridge.
Execute the followings if the type of the ink cartridge is
correct.
2. Check the assembly of the ID Contact PCB and the
shape of the contact plate, and execute the cleaning.
3. Check the connection of the ID Contact PCB.
4. Replace the Cartridge with a new one
5. Replace the ID Contact PCB Assy. with a new one.
(Refer to 3.3.3)
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
48
ERROR 60d
REMAIN INK
Remaining ink is not enough to execute
cleaning or to fill ink.
Replace the Cartridge with a new one
49
ERROR 60e
NOT COMPLETE FUP
Ink is not filled into some heads. Fill ink into unfilled heads.
50
ERROR 60f
Expiration
Some ink cartridges are expired. 1. Check the expiration date of the ink.
(If this message appears when a correct cartridge is set)
2. Check the assembly of the ID Contact PCB and the
shape of the contact plate, and execute the cleaning.
3. Check the connection of the ID Contact PCB.
4. Replace the Cartridge with a new one.
5. Replace the ID Contact PCB Assy. with a new one.
(Refer to 3.3.3)
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
51
ERROR 610
NOT FILLUP
Ink is not filled into all the heads. Fill ink to all the heads.
52
ERROR 611
Case Weight
"CASE WEIGHT" of 600ml cartridge is not
set.
Set "CASE WEIGHT" for "600ml CARTRIDGE" of
"MACHINE SET".
53
ERROR 612
INK LVL LOW
Remaining amount of ink became less. Enter the cartridge weight from "CART WEIGHT" menu of
"SET UP".
54
ERROR 613
INK LVL END
Remaining amount of ink became none.  If ink remains, enter the cartridge weight from "CART
WEIGHT" menu of "SET UP".
 If ink does not remain, replace it with a new cartridge.
55
ERROR 614
Preservation Failure
Remaining amount of ink was failed to be
written.
1. Pull the cartridge out and then insert it to write it again.
2. If the error cannot be solved, replace it with a new cartridge.
56
ERROR 615
Cartridge Weight
The cartridge weight was not entered. Enter the cartridge weight.
57
ERROR 702
THERMISTOR
Defective of the thermistor (disconnection
or short)
1. Check each thermistor.
2. Replace the Main PCB with a new one. (Refer to 3.3.1)
58
ERROR 705
WATER LACK
Water in the cooling water buffer tank is
low.
1. Check amount of water in the cooling water buffer
tank, and replace the Nonfreezing fluid mixture water
if lacking.
2. If water decreases quickly, check water leakage from
the cooling water path (a tube or a radiator).
• Execute [#TEST SENSOR TEST]->[CoolFloat] to
check the sensor operation.
3. Check the assembly of the Float Sensor and the
connector connection.
4. Replace the Float Sensor and the Cable with a new
one.
5. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
 List of Error Messages (7/9)
No. LCD Cause List of Countermeasures
R.2.0
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model UJF-3042/FX Issued 2010.08.27 Revised 2011.09.30 F/W ver 1.80 / 1.00 Remark
2.0
Rev.