MIMAKI UJF-3042 - List of Error Messages

© 2013 MIMAKI ENGINEERING CO.,LTD.
7.1.2 P.1
1
2
3
4
5
6
7
8
R.2.0
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model UJF-3042/FX Issued 2010.08.27 Revised 2011.09.30 F/W ver 1.80 / 1.00 Remark
2.0
Rev.
7.1.2 List of Error Messages
 List of Error Messages (1/9)
No. LCD Cause List of Countermeasures
1
ERROR 108
HD CONNECT[12345678]
Head connection error
(Head connection can not be confirmed)
1. Check the setting of loading number of the head in the
parameter.
(System parameter No.41 HEAD NO=3)
2. Disconnect and connect the FFC located between the
Slider PCB and the SL-Relay PCB.
3. Check connection between the Slider PCB from the
Print Head
4. Replace the Slider PCB with a new one.
(Refer to 6.4.5)
5. Replace the Print Head with a new one. (Refer to 6.2.1)
2
ERROR 108
HD THERMIS[12345678]
Head thermistor
(Head temperature can not be measured)
3
ERROR 12e
Head Faild[xxxx]
(The details of [xxxx] are
explained below this
list.)
Abnormality of the Print head.
Abnormality of the Driver of the Print
head.
1. Update F/W.
2. Initialize a parameter.
3. Disconnect and connect the FFC located between the
Slider PCB and the SL-Relay PCB.
4. Replace the FFC located between the Slider PCB and
the SL-Relay PCB.
5. Replace the Print Head with a new one. (Refer to 6.2.1)
6. Replace the Slider PCB with a new one.
(Refer to 6.4.5)
7. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
4
ERROR 122
CHECK:SDRAM
PRAM size is not sufficient at FW
upgrading (fw_updmsg).
1. Update F/W.
2. Replace the Main PCB with a new one. (Refer to 3.3.1)
5
ERROR 128
HDC FIFO OVER
HDC FIFO OVER error
(Data transmission speed is too fast
Control PCB trouble)
HDC FIFO OVERRUN is detected at the
scan slider process (ScanSlider)
1. Check the parameter.
(Is the scan parameter the default value?)
2. Update F/W.
3. Check if there is no data error from RIP.
4. To make sure, repeat RIP.
5. Disconnect and connect the FFC located between the
Main PCB and the SL-Relay PCB.
6. Disconnect and connect the FFC located between the
SL-Relay PCB and the Slider PCB.
7. Replace the FFC located between the Main PCB and
the SL-Relay PCB.
8. Replace the FFC located between the SL-Relay PCB
and the Slider PCB.
9. Replace the Slider PCB with a new one.
(Refer to 6.4.5)
10. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
11. Replace the Main PCB with a new one. (Refer to 3.3.1)
6
ERROR 128
HDC FIFO UNDER
HDC FIFO UNDER error
(Data transmission speed is too slow
Control PCB trouble)
HDC FIFO UNDERRUN is detected at the
scan slider process (ScanSlider)
7
ERROR 129
BATTERY EXCHANGE
Battery dead (RTC battery dead is
detected.)
Proper information of Printer or Time
(Dedicated IC) unusable on Printer
initializing process (opinit).
1. Replace a battery equipped on the Main PCB with new
one. (CR2032)
* The new battery should be the same product or the
equivalent.
* Discard the old battery according to the instruction
from the maker.
8
ERROR 130
HD DATA SEQ
Head data transferring sequence error 1. Disconnect and connect the FFC located between the
Slider PCB and the SL-Relay PCB.
2. Disconnect and connect the FFC located between the
SL-Relay PCB and the Main
PCB.
3. Replace the FFC located between the Slider PCB and
the SL-Relay PCB.
4. Replace the FFC located between the SL-Relay PCB
and the Main
PCB.
5. Replace the Slider PCB with a new one.
(Refer to 6.4.5)
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
7. Replace the Main PCB with a new one. (Refer to 3.3.1)