Scanlab RTC 5 PC Interface Board - Page 224

RTC
®
5 PC Interface Board
Rev. 1.9 e
10 Commands And Functions
224
innovators for industry
Starting and Stopping Lists via External
Control Signals and Master/Slave Synchroni-
zation
(n_) set_control_mode_list
nor
...................... 413
(n_) set_extstartpos_list
us
............................ 421
List Handling and Structured Programming
(n_) list_continue
nor
...................................... 317
(n_) list_jump_pos
us
..................................... 319
(n_) list_jump_rel
us
....................................... 321
(n_) list_nop
nor
.............................................. 322
(n_) list_repeat
us
........................................... 323
(n_) list_until
us
.............................................. 325
(n_) long_delay
nor
......................................... 348
(n_) set_end_of_list
nor
.................................. 420
(n_) set_list_jump
us
...................................... 447
(n_) set_wait
nor
............................................. 500
Subroutine Commands
(n_) list_call
us
................................................ 315
(n_) list_call_abs
us
......................................... 316
(n_) list_return
us
........................................... 324
(n_) sub_call
us
............................................... 525
(n_) sub_call_abs
us
........................................ 525
Setting the Laser Parameters
(n_) config_laser_signals_list
ds
.................... 242
(n_) set_auto_laser_params_list
ds
................ 409
(n_) set_encoder_speed
ds
............................. 418
(n_) set_firstpulse_killer_list
us
...................... 423
(n_) set_laser_delays
us
.................................. 442
(n_) set_laser_pin_out_list
us
......................... 444
(n_) set_laser_pulses
ds
.................................. 445
(n_) set_laser_timing
ds
................................. 446
(n_) set_pulse_picking_list
nor
....................... 471
(n_) set_qswitch_delay_list
us
....................... 471
(n_) set_softstart_level_list
nor
...................... 485
(n_) set_softstart_mode_list
var
.................... 487
(n_) set_standby_list
ds
.................................. 489
(n_) set_vector_control
us
.............................. 498
Setting the Scanner Parameters
(n_) set_delay_mode_list
mul
......................... 416
(n_) set_jump_speed
us
.................................. 438
(n_) set_mark_speed
ds
.................................. 448
(n_) set_scanner_delays
ds
............................. 475
(n_) set_sky_writing_limit_list
us
................... 478
(n_) set_sky_writing_list
nor
.......................... 478
(n_) set_sky_writing_mode_list
nor
............... 480
(n_) set_sky_writing_para_list
nor
................. 483
Coordinate Transformations
(n_) set_angle_list
var
..................................... 406
(n_) set_defocus_list
var (1)
............................ 415
(n_) set_matrix_list
var
................................... 450
(n_) set_offset_list
var
.................................... 463
(n_) set_offset_xyz_list
var (1)
........................ 465
(n_) set_scale_list
var
...................................... 475
Online Positioning
(n_) apply_mcbsp_list
nor
.............................. 231
(n_) set_mcbsp_matrix_list
us
........................ 454
(n_) set_mcbsp_rot_list
us
.............................. 457
(n_) set_mcbsp_x_list
us
................................. 458
(n_) set_mcbsp_y_list
us
................................. 459
Direct Laser and Scan Head Control
(n_) laser_on_list
var
....................................... 311
(n_) laser_on_pulses_list
var
........................... 312
(n_) laser_signal_off_list
nor
.......................... 313
(n_) laser_signal_on_list
nor
........................... 314
(n_) para_laser_on_pulses_list
var
................. 375
Scanning Raster Images (Bitmaps)
(n_) set_default_pixel_list
us
.......................... 414
(n_) set_n_pixel
var
......................................... 462
(n_) set_pixel
var
............................................. 466
(n_) set_pixel_line
nor
..................................... 467
(n_) set_pixel_line_3d
mul (1)
.......................... 468
I/O Commands
(n_) clear_io_cond_list
us
............................... 241
(n_) read_io_port_list
us
................................. 387
(n_) rs232_write_text_list
var
......................... 396
(n_) set_free_variable_list
us
.......................... 433
(n_) set_io_cond_list
us
.................................. 435
(n_) set_mcbsp_out
us
................................... 455
(n_) write_8bit_port_list
ds
............................ 557
(n_) write_da_1_list
ds
................................... 557
(n_) write_da_2_list
ds
................................... 558
(n_) write_da_x_list
ds
.................................... 558
(n_) write_io_port_list
ds
............................... 559
(n_) write_io_port_mask_list
ds
..................... 560
(1) Only with enabled 3D option.
nor normal list command
var variable list command
us undelayed short list command
ds delayed short list command
mul list multi-command