Siemens SIMATIC ET 200S - Page 12

Contents
x
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
5 Wiring and Fitting 5-1...................................................
5.1 General rules and regulations for operating the ET 200S 5-1...........
5.2 Operating the ET 200S on a grounded supply 5-3....................
5.3 Electrical design of the ET 200S 5-6................................
5.4 Wiring the ET 200S 5-7...........................................
5.4.1 Wiring a terminal module with screw-type terminals 5-8...............
5.4.2 Wiring a terminal module with spring terminals 5-8...................
5.4.3 Wiring terminal modules with Fast Connect 5-10......................
5.4.4 Wiring terminal modules 5-13.......................................
5.4.5 Wiring the IM151-1 BASIC, IM151-1 STANDARD and
IM151-1 HIGH FEATURE interface modules 5-18.....................
5.4.6 Wiring the IM151-3 PN interface module 5-19.........................
5.4.7 Wiring the IM151-1 FO STANDARD interface module 5-21.............
5.5 Inserting and identifying the electronic modules 5-24...................
5.6 Assigning device names for the I/O device 5-30.......................
6 Commissioning and Diagnostics 6-1.....................................
6.1 Commissioning and diagnostics on PROFIBUS DP 6-1...............
6.1.1 Configuring the ET 200S on PROFIBUS DP 6-2.....................
6.1.2 Commissioning and startup of the ET 200S on PROFIBUS DP 6-10.....
6.1.3 Diagnosis using the LEDs 6-12.....................................
6.1.4 Diagnostic messages of the electronic modules 6-22..................
6.1.5 Evaluating the interrupts of the ET 200S 6-23.........................
6.1.6 Diagnostics using STEP 5 and STEP 7 6-25..........................
6.1.6.1 Reading out the diagnosis 6-25.....................................
6.1.6.2 Structure of slave diagnostic data 6-29...............................
6.1.6.3 Station statuses 1 to 3 6-31........................................
6.1.6.4 Master PROFIBUS Address 6-33...................................
6.1.6.5 Manufacturer ID 6-33..............................................
6.1.6.6 Module diagnosis 6-34.............................................
6.1.6.7 Module information 6-36...........................................
6.1.6.8 Channel-specific diagnosis 6-38....................................
6.1.6.9 Interrupts 6-48....................................................
6.1.6.10 Diagnostics in the case of invalid ET 200S configuration states
on the PROFIBUS DP 6-56........................................
6.2 Commissioning and diagnostics on PROFINET IO 6-57................
6.2.1 Configuring the ET 200S on PROFINET IO 6-57......................
6.2.2 Commissioning and startup of the ET 200S on PROFINET IO 6-59......
6.2.3 Diagnosis using the LEDs 6-61.....................................
6.2.4 Diagnostic messages of the electronic modules 6-64..................
6.2.5 Evaluating the interrupts of the ET 200S 6-65.........................
6.2.6 Diagnostics with STEP 7 6-66......................................
6.2.6.1 Reading out the diagnosis 6-67.....................................
6.2.6.2 Channel diagnostics 6-68..........................................
6.2.6.3 Diagnostics in the case of invalid ET 200S configuration states
on the PROFINET IO 6-70.........................................
6.2.6.4 Diagnostics in the case of interruption of the ET 200S backplane bus 6-70
6.2.6.5 Diagnostics in the case of failure of the load voltage
from the power module 6-71........................................
6.2.6.6 Diagnosis after a STOP of the I/O controller or after restart
of the O/O device 6-71............................................