Siemens SIMATIC ET 200S - Page 20

Contents
xviii
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
12-5 Smoothing with 2AI U Standard, 2AI U High Feature,
2AI I 2WIRE Standard, 2AI I 4WIRE Standard,
2AI I 2/4WIRE High Feature, 2AI RTD Standard, 2AI RTD High Feature,
2AI TC Standard, 2AI TC High Feature 12-39..........................
12-6 Smoothing with 2AI U High Speed, 2AI I 2WIRE High Speed,
2AI I 4WIRE High Speed 12-40......................................
12-7 Block diagram of the 2AI U Standard 12-44............................
12-8 Block diagram of the 2AI U High Feature 12-48........................
12-9 Block diagram of the 2AI U High Speed 12-52.........................
12-10 Block diagram of the 2AI I 2WIRE Standard 12-56......................
12-11 Block diagram of the 4AI I 2WIRE Standard 12-59......................
12-12 Block diagram of the 2AI I 2WIRE High Speed 12-64...................
12-13 Block diagram of the 2AI I 4WIRE Standard 12-68......................
12-14 Block diagram of the 2AI I 2/4WIRE High Feature 12-72................
12-15 Block diagram of the 2AI I 4WIRE High Speed 12-76...................
12-16 Block diagram of the 2AI RTD Standard 12-80.........................
12-17 Block diagram of the 2AI RTD High Feature 12-85......................
12-18 Block diagram of the 2AI TC Standard 12-92..........................
12-19 Block diagram of the 2AI TC High Feature 12-96.......................
12-20 Block diagram of the 2AO U Standard 12-101...........................
12-21 Block diagram of the 2AO U High Feature 12-105.......................
12-22 Block diagram of the 2AO I Standard 12-109...........................
12-23 Block diagram of the 2AO I High Feature 12-113........................
13-1 Synchronization group 13-5........................................
13-2 Reflection light probe 13-6.........................................
13-3 Reflection light barrier 13-6.........................................
13-4 Differential travel parameter 13-7...................................
13-5 Time value, time functions parameter 13-8...........................
13-6 Mode of Operation: Preset of a sensitivity/distance value (IntelliTeach) 13-13
13-7 Mode of Operation: Teach-in 13-14...................................
13-8 Block diagram of the 4 IQ-SENSE 13-16..............................
A-1 Explanation of the abbreviated designation A-2......................
B-1 Minimum clearances B-1..........................................
B-2 IM151-1 interface module dimension drawing B-2....................
B-3 Interface Module IM151-3 PN dimension drawing B-2.................
B-4 Dimension drawing for terminal modules (screw-type/spring terminals)
with an electronic module inserted B-3..............................
B-5 Dimension drawing for terminal modules (screw-type/spring terminals)
with an electronic module inserted B-4..............................
B-6 Dimension drawing for terminal modules (screw-type/spring terminals)
with an electronic module inserted B-5..............................
B-7 Dimensioned drawing of a terminal module (screw-type terminal)
with an electronic module inserted B-5..............................
B-8 Dimensioned drawing of terminal modules (Fast Connect)
with an electronic module inserted B-6..............................
B-9 Dimensioned drawing of terminal modules (Fast Connect)
with an electronic module inserted B-7..............................
B-10 Terminating module dimensioned drawing B-8.......................
B-11 Shield contact dimension drawing B-8..............................
D-1 Response times between DP master and ET 200S D-1...............
D-2 Example setup for calculating the response time in the case
of the IM151-1 BASIC D-2.........................................
D-3 Example of the calculation of the response time in the case
of the IM151-1 STANDARD, IM 151-1 FO STANDARD D-3............