February, 2008
6-20
WorkCentre 5225, 5230
IOT NVM List
Launch Version
General Procedures
763-628 NVM_Dual_Staple_Stack_Set_Limit_S_Size 75 1~255 Maximum number of small-sized copies allowed in the Stacker in unstaple, single sta-
ple, and dual staple mode.
763-629 NVM_Dual_Staple_Stack_Set_Limit_L_Size 75 1~255 Maximum number of large-sized copies allowed in the Stacker in unstaple, single sta-
ple, and dual staple mode.
763-630 NVM_Max_Stapling_50Sheets 50 25~75 Maximum number of sheets than can be stapled using a 50-sheet Staple Cartridge.
763-631 NVM_Puncher_Full_Count_Num_24 - 1, 2 Digit 50 0~99 The number of sheets required to generate a Puncher Rubbish Full message (2-4 hole
punch). Effective when NVM 763-605 is 5.
763-631 NVM_Puncher_Full_Count_Num_24 - 3, 4 Digit 7 0~15
763-631 NVM_Puncher_Full_Count_Num_24 - 5, 6 Digit 0 0~0
763-632 [Unused] NVM_Eject_Exit_Ctrl_Encoder_Limit 0 0~255 [Unused] When the Encoder position reaches this value, the eject speed is switched.
763-633 NVM_Bklt_Stpl_Full_Stack_Pos_Encoder_S_Size 90 1~90 Full stack positional Encoder limitation during booklet staple mode for small size paper
(paper size < B4).
763-634 NVM_Bklt_Stpl_Full_Stack_Pos_Encoder_L_Size 90 1~90 Full stack positional Encoder limitation during booklet staple mode for large size paper
(paper size = or > B4).
763-635 NVM_Bklt_Unstpl_Full_Stack_Pos_Encoder_S_Siz
e
90 1~90 Full stack positional Encoder limitation during booklet unstaple mode for small size
paper (paper size < B4).
763-636 NVM_Bklt_Unstpl_Full_Stack_Pos_Encoder_L_Siz
e
90 1~90 Full stack positional Encoder limitation during booklet unstaple mode for large size
paper (paper size = or > B4).
763-637 NVM_Bklt_Staple_Stack_Sheet_Limit 60 1~200 Maximum number of sheets allowed in the Stacker during booklet staple mode.
763-638 NVM_Bklt_Unstaple_Stack_Sheet_Limit 50 1~200 Maximum number of sheets allowed in the Stacker during booklet unstaple mode.
763-639 NVM_Puncher_Near_Full_Count_Num_24 - 1, 2
Digit
0 0~99 Sheet count when punch rubbish warning is declared (valid when NVM 763-605 = 5).
763-639 NVM_Puncher_Near_Full_Count_Num_24 - 3, 4
Digit
5 0~15
763-641 NVM_Thick_Paper_Puncher_Count 1 1~5 Adjusts sheet count for NVM 763-639 to compensate for thick paper.
763-642 NVM_Pre_Punch_Stop_Pulse_B4_More 100 0~120 Number of pulses between stopping of Transport Motor and paper punch (paper length
= or > 364.0 mm [B4]).
763-643 NVM_Pre_Punch_Stop_Pulse_B4_Less 100 0~120 Number of pulses between stopping of Transport Motor and paper punch (paper length
< 364.0 mm [B4]).
763-644 NVM_Pre_Punch_Stop_Tim 5 5~100 Time delay until punch operation starts.
763-645 NVM_Pre_Fold_Stop_Pulse_B4_More 100 0~200 Number of pulses between stopping of Transport Motor and paper fold (paper length =
or > 364.0 mm [B4]).
763-646 NVM_Pre_Fold_Stop_Pulse_B4_Less 100 0~200 Number of pulses between stopping of Transport Motor and paper fold (paper length <
364.0 mm [B4]).
763-647 NVM_Pre_Fold_Stop_Tim 5 5~100 Time delay until fold operation starts.
763-648 NVM_Stk_Eject_Exit_Speed_Mode 79 1~255 Eject exit speed in Stacker job mode.
763-649 NVM_Tmp_Strt_Tim 250 0~250 Time delay until tamping operation starts.
763-650 NVM_Set_Clmp_Off_Tim 120 0~200 Off time for the Set Clamp Clutch after paper is outputted.
Usage: 200 + NVM_Set_Clmp_Off_Tim (initialize 300 ms).
763-651 NVM_Stk_Sub_Pdl_Sol_Strt_Tim 100 0~200 Time between Compile Exit Sensor OFF and Sub Paddle Solenoid ON during job stack-
ing mode.
Usage: 25 (5 with Filter) + NVM_Stk_Sub_Pdl_Sol_Strt_Tim = operation start time (ini-
tialize 70 [50] ms)
Table 13 SB Finisher
Chain-link Name Default Range 1 Count Remarks
To Next Page
Loading...
Need help?
General
