YASKAWA CIMR-G5A Series - Page 345

12.5 User Constants
12 - 17
Table 12.1 User Constants (Continued)
No.
Name
(Display)
Factory
Setting
Setting No.
Name
(Display)
Factory
Setting
Setting
E1-11
Mid. output frequency 2
:
2
(Mid Frequency B)
0.0
F1-06
PG division rate (PG pulse monitor)
(PG output Ratio)
1
E1-12
Mid. output frequency voltage 2
:
2
Mid Voltage B)
0.0
F1-07
Integral value during accel/decel enable/disable
(PG Ramp PI/I Sel)
0
E1-13
Base voltage
:
2
(Base Voltage)
0.0
F1-08
Overspeed detection level
(PG Overspd Level)
115
E2-01
Motor rated current
(Motor Rated FLA)
1.90
:
3
F1-09
Overspeed detection delay time
(PG Overspd Time)
0.0
:
4
E2-02
Motor rated slip
(Motor Rated Slip)
2.90
:
3
F1-10
Excessive speed deviation detection level
(PG Deviate level)
10
E2-03
Motor no-load current
(No-Load Current)
1.20
:
3
F1-11
Excessive speed deviation detection delay time
(PG Deviate Time)
0.5
E2-04
Number of motor poles
(Number of Poles)
4
F1-12
Number of PG gear teeth 1
(PG# Gear Teeth 1)
0
E2-05
Motor line-to-line resistance
(Term Resistance)
9.842
:
3
F1-13
Number of PG gear teeth 2
(PG# Gear Teeth 2)
0
E2-06
Motor leak inductance
(Lead Inductance)
18.2
:
3
F1-14
PG open-circuit detection time
:
1
(PGO Time)
2.0
E2-07
Motor iron saturation coefficient 1
(Saturation Comp 1)
0.50
F2-01
Bi-polar or uni-polar input selection
(AI-14 Input Sel)
0
E2-08
Motor iron saturation coefficient 2
(Saturation Comp 2)
0.75
F3-01
Digital input option
(DI Input)
0
E2-09
Motor mechanical loss
(Mechanical Loss)
0.0
F4-01
Channel 1 monitor selection
(AO Ch1 Select)
2
E2-10
Motor iron loss for torque compensation
(Tcomp Iron Loss)
14
:
3
F4-02
Channel I gain
(AO Ch1 Gain)
1.00
E3-01
Motor 2 control method selection
:
1
(Control Method)
2
F4-03
Channel 2 monitor selection
(AO Ch2 Select)
3
E4-01
Motor 2 max. output frequency
:
1
(V/F2 Max Freq)
60.0
F4-04
Channel 2 gain
(AO Ch2 Gain)
0.50
E4-02
Motor 2 max. voltage
:
1
(V/F2 Max Voltage)
200.0
:
2
F4-05
Channel 1 output monitor bias
(AO Ch1 Bias)
0.0
E4-03
Motor 2 max. voltage frequency
:
1
(V/F2 Base Freq)
60.0
F4-06
Channel 2 output monitor bias
(AO Ch2 Bias)
0.0
E4-04
Motor 2 mid. output frequency 1
:
1
(V/F2 Mid Freq)
3.0
F5-01
Channel 1 output selection
(DO-02 Ch1 Select)
0
E4-05
Motor 2 mid. output frequency voltage 1
:
1
(V/F2 Mid Voltage)
11.0
:
2
F5-02
Channel 2 output selection
(DO-02 Ch2 Select)
1
E4-06
Motor 2 min. output frequency
(V/F2 Min Freq)
0.5
F6-01
Output mode selection
(DO-08 Selection)
0
E4-07
Motor 2 min. output frequency voltage
:
1
(V/F2 Min Voltage)
2.0
:
2
F7-01
Frequency multiple selection
(PO-36F Selection)
1
E5-01
Motor 2 rated current
:
1
(Motor 2 rated FLA)
1.9
:
3
F8-01
Transmission option (SI-F/G)
:
1
(E-15 Det Sel)
1
E5-02
Motor 2 rated slip
:
1
(Motor 2 Slip Freq)
2.90
:
3
F9-01
External fault input level from transmission op-
tion (FF0 Selection)
:
1
0
E5-03
Motor 2 no-load current
:
1
(Motor 2 No-load I)
1.20
:
3
F9-02
External fault detection from transmission op-
tion (EF0 Detection)
:
1
0
E5-04
Motor 2 number of poles
:
1
(Motor 2 # poles)
4 poles
F9-03
Action for external fault from transmission op-
tion (EF0 Fault Act)
:
1
1
E5-05
Motor 2 line-to-line resistance
(Motor 2 Term Ohms)
9.842
:
3
F9-04
Transmission option trace sampling time
(Trace Sample Time)
:
1
0
E5-06
Motor 2 leak inductance
:
1
(Motor 2 Leak)
18.2
:
3
F9-05
Torque reference/ torque limit selection from
non-SI-K2 transmission cards
(Torq Ref/Lmt Sel)
1
F1-01
PG constant
(PG Pulse/Rev)
600
F9-06
Operation selection for non-SI-K2 transmission
error detection
(BUS Fault Sel)
1
F1-02
Operation selection at PG open circuit
(PG Fdbk Loss Sel)
1
H1-01
Multi-function input (terminal 3)
(Terminal 3 Sel)
24
F1-03
Operation selection at overspeed
(PG Overspeed Sel)
1
H1-02
Multi-function input (terminal 4)
(Terminal 4 Sel)
14
F1-04
Operation selection at deviation
(PG Deviation Sel)
3
H1-03
Multi-function input (terminal 5)
(Terminal 5 Sel)
3 (0)
:
5
F1-05
PG rotation
(PG Rotation Sel)
0
H1-04
Multi-function input (terminal 6)
(Terminal 6 Sel)
4 (3)
:
5
* 1. Not displayed for some models depending on software version No.
* 2. Setting for 200 V class Inverters. For 400 V class Inverters, double the value.
* 3. Setting unit and initial setting depend on Inverter capacity.
* 4. Depends on the control method (A1-02).
* 5. Factory setting in the parentheses is for 3-wire sequence.
12