Amazone AMAPAD - Page 109

To Next Page

To Previous Page

1. Tap on any data field on the dashboard.

The selection list for the data fields will be opened.

2. Select the desired data fields

3. Confirm with

G | Using the operating menu | Configuring the dashboard

MG5574-EN-II | B.1 | 25.10.2016

107

Main Page

Default Chapter3
- Table of Contents3
A about this Operating Manual6
- Meaning of the Operating Manual6
- Validity6
- Other Applicable Documents6
- Diagrams7
- Your Opinion Is Important9
B Assembly Instructions10
C AMAPAD at a Glance11
- Connections and Buttons11
- Basic Buttons and Leds11
D Basic Operation12
- Switching on the AMAPAD12
- Switching off the AMAPAD13
- Resetting the AMAPAD14
- Using the Touchscreen14
- Using the Basic Buttons15
- Switching between the Main Menus16
E User Interface at a Glance18
- General Warning Messages18
- Warning Messages from the Universal Terminal18
- General Control Elements19
- Buttons in the Operating Menu21
Configuring the AMAPAD26
- Using the Setup Menu26
- Entering the User Settings27
- Entering the System Settings44
- Configuring a Vehicle73
- Configuring an Implement84
G Using the Operating Menu100
- Using the Function Menu101
- Using the Map View104
- Configuring the Dashboard107
  - Adding Data Fields108
  - Editing Data Fields110
H Working Without a Job112
- Configuring the Quick Start112
- Calling up the Quick Start113
I Managing Jobs114
- Using the Job Menu115
- Using the Job Assistant115
- Using the Quick Start116
- Editing Master Data116
- Starting a Job117
- Creating a New Job118
- Importing Job Data120
- Exporting Task Data121
- Selecting a Job123
  - Filtering Jobs124
  - Sorting Jobs124
- Deleting a Job125
- Editing Job Data126
- Calling up Job Information126
- Define Working Time127
J Managing Fields129
- Creating a New Field129
- Creating a Boundary Line131
- Editing the Boundary Line137
- Configuring the Headlands139
  - Configuring Headland Actions140
- Deleting All Boundary Lines142
- Setting Flag Point142
Using Track Lines148
- Creating Track Lines149
- Re-Using Track Lines156
- Following Track Lines157
  - Checking the Track Deviation with Lightbars158
  - Checking the Track Deviation with the Dashboard158
- Correcting the Track Lines159
Correcting the GPS Reception160
- Performing the GPS Drift Correction160
  - Correcting the GPS Drift with the GPS Drift Options161
  - Correcting the GPS Drift with a Flag Point162
- Correcting the Track Lines163
- Saving the Corrected Track Lines165
- Calling up GPS Information166
M Using Automatic Steering168
- Steering Calibration168
- Calling up the Steering Status170
- Coordinating the Automatic Steering172
- Switching on the Automatic Steering174
  - Delayed Automatic Steering Switch-On174
- Switching off the Automatic Steering175
N Using the Universal Terminal176
- Opening the Universal Terminal177
- Enlarging the Section in the Miniature View178
- Using Automatic AUX-N Assignments178
- Managing AUX-N Functions180
O Using Automatic Reverse Drive Detection185
P Using Part-Width Section Control186
- Using Manual Part-Width Section Control186
- Using Automatic Part-Width Section Control188
  - Configuring the Control Mode189
  - Defining the Boundary Limit193
Q Using Rate Control196
- Using a Job with Application Map197
- Adding an Application Map to a Job198
- Defining a Fixed Setpoint for Rate Control201
- Configuring Peer Control for Rate Control203
- Configuring Rate Control205
- Selecting the Coverage Map211
- Selecting the VRC Map213
- Configuring the Coverage Scale214
  - Defining the Application Rate Ranges Based on the Application Rate216
Managing Inventory Data218
- Using the Inventory Manager218
- Exporting Job Data Backups219
S Using the Multi-Function Button221
- Using the Global Start Screens221
- Taking Screenshots222
Troubleshooting224
- Error Codes224
- Calling up the System Diagnosis226
- Determining the Software Version227
- LED Display227
- Contact to AMAZONE229
Indexes232
- Index232

Related product manuals

Amazone AMAPAD - Page 109

Table of Contents

Related product manuals