Amazone AMAPAD - Calling Up the Quick Start

To Next Page

To Previous Page

3. Choose the desired data for the selected data field.

4. Confirm with .

G | Using the operating menu | Configuring the dashboard

MG5574-EN-II | B.1 | 25.10.2016

109

Main Page

Default Chapter3
- Table of Contents3
A about this Operating Manual6
- Meaning of the Operating Manual6
- Validity6
- Other Applicable Documents6
- Diagrams7
- Your Opinion Is Important9
B Assembly Instructions10
C AMAPAD at a Glance11
- Connections and Buttons11
- Basic Buttons and Leds11
D Basic Operation12
- Switching on the AMAPAD12
- Switching off the AMAPAD13
- Resetting the AMAPAD14
- Using the Touchscreen14
- Using the Basic Buttons15
- Switching between the Main Menus16
E User Interface at a Glance18
- General Warning Messages18
- Warning Messages from the Universal Terminal18
- General Control Elements19
- Buttons in the Operating Menu21
Configuring the AMAPAD26
- Using the Setup Menu26
- Entering the User Settings27
- Entering the System Settings44
- Configuring a Vehicle73
- Configuring an Implement84
G Using the Operating Menu100
- Using the Function Menu101
- Using the Map View104
- Configuring the Dashboard107
  - Adding Data Fields108
  - Editing Data Fields110
H Working Without a Job112
- Configuring the Quick Start112
- Calling up the Quick Start113
I Managing Jobs114
- Using the Job Menu115
- Using the Job Assistant115
- Using the Quick Start116
- Editing Master Data116
- Starting a Job117
- Creating a New Job118
- Importing Job Data120
- Exporting Task Data121
- Selecting a Job123
  - Filtering Jobs124
  - Sorting Jobs124
- Deleting a Job125
- Editing Job Data126
- Calling up Job Information126
- Define Working Time127
J Managing Fields129
- Creating a New Field129
- Creating a Boundary Line131
- Editing the Boundary Line137
- Configuring the Headlands139
  - Configuring Headland Actions140
- Deleting All Boundary Lines142
- Setting Flag Point142
Using Track Lines148
- Creating Track Lines149
- Re-Using Track Lines156
- Following Track Lines157
  - Checking the Track Deviation with Lightbars158
  - Checking the Track Deviation with the Dashboard158
- Correcting the Track Lines159
Correcting the GPS Reception160
- Performing the GPS Drift Correction160
  - Correcting the GPS Drift with the GPS Drift Options161
  - Correcting the GPS Drift with a Flag Point162
- Correcting the Track Lines163
- Saving the Corrected Track Lines165
- Calling up GPS Information166
M Using Automatic Steering168
- Steering Calibration168
- Calling up the Steering Status170
- Coordinating the Automatic Steering172
- Switching on the Automatic Steering174
  - Delayed Automatic Steering Switch-On174
- Switching off the Automatic Steering175
N Using the Universal Terminal176
- Opening the Universal Terminal177
- Enlarging the Section in the Miniature View178
- Using Automatic AUX-N Assignments178
- Managing AUX-N Functions180
O Using Automatic Reverse Drive Detection185
P Using Part-Width Section Control186
- Using Manual Part-Width Section Control186
- Using Automatic Part-Width Section Control188
  - Configuring the Control Mode189
  - Defining the Boundary Limit193
Q Using Rate Control196
- Using a Job with Application Map197
- Adding an Application Map to a Job198
- Defining a Fixed Setpoint for Rate Control201
- Configuring Peer Control for Rate Control203
- Configuring Rate Control205
- Selecting the Coverage Map211
- Selecting the VRC Map213
- Configuring the Coverage Scale214
  - Defining the Application Rate Ranges Based on the Application Rate216
Managing Inventory Data218
- Using the Inventory Manager218
- Exporting Job Data Backups219
S Using the Multi-Function Button221
- Using the Global Start Screens221
- Taking Screenshots222
Troubleshooting224
- Error Codes224
- Calling up the System Diagnosis226
- Determining the Software Version227
- LED Display227
- Contact to AMAZONE229
Indexes232
- Index232

Amazone AMAPAD - Calling Up the Quick Start

Table of Contents

Related product manuals