Fuji Electric FRENIC-Ace series - Page 8

vi
6.3 If an Alarm Code Appears on the LED Monitor .................................................................................. 6-3
6.3.1 Alarm code list ............................................................................................................................... 6-3
6.3.2 Causes, checks and measures of alarms ..................................................................................... 6-6
[ 1 ] cof PID feedback wire break ................................................................................................ 6-6
[ 2 ] dba Braking transistor broken ............................................................................................... 6-6
[ 3 ] dbh Braking resistor overheat ............................................................................................... 6-6
[ 4 ] ecf EN circuit failure ............................................................................................................. 6-7
[ 5 ] ecl Customizable logic failure .............................................................................................. 6-7
[ 6 ] ef Ground fault ..................................................................................................................... 6-7
[ 7 ] er1 Memory error ................................................................................................................. 6-7
[ 8 ] er2 Keypad communications error ....................................................................................... 6-8
[ 9 ] er3 CPU error ...................................................................................................................... 6-8
[ 10 ] er4 Option communications error ......................................................................................... 6-8
[ 11 ] er5 Option error ................................................................................................................... 6-8
[ 12 ] er6 Operation error .............................................................................................................. 6-9
[ 13 ] er7 Tuning error ................................................................................................................... 6-9
[ 14 ] er8 RS-485 communications error (Communications port 1)/
erp RS-485 communications error (Communications port 2) ............................................. 6-10
[ 15 ] erd Step-out detection/detection failure of magnetic pole position at startup ...................... 6-11
[ 16 ] ere Speed inconsistency / Excessive speed deviation ....................................................... 6-12
[ 17 ] erf Data saving error during undervoltage ......................................................................... 6-13
[ 18 ] erh Hardware error ............................................................................................................. 6-13
[ 19 ] ero Positioning control error ............................................................................................... 6-13
[ 20 ] err Simulated failure .......................................................................................................... 6-14
[ 21 ] ert CAN communications failure ........................................................................................ 6-14
[ 22 ] fus DC fuse-blowing .......................................................................................................... 6-14
[ 23 ] lin Input phase loss ........................................................................................................... 6-15
[ 24 ] lu Undervoltage .................................................................................................................. 6-15
[ 25 ] 0cn Instantaneous overcurrent ........................................................................................... 6-16
[ 26 ] 0h1 Cooling fin overheat ..................................................................................................... 6-17
[ 27 ] 0h2 External alarm.............................................................................................................. 6-17
[ 28 ] 0h3 Inverter internal overheat ............................................................................................. 6-17
[ 29 ] 0h4 Motor protection (PTC thermistor) ............................................................................... 6-18
[ 30 ] 0h6 Charging resistor overheat ........................................................................................... 6-18
[ 31 ] 0ln Motor overloads 1 to 2 ................................................................................................. 6-19
[ 32 ] 0lu Inverter overload .......................................................................................................... 6-20
[ 33 ] 0pl Output phase-failure detection ..................................................................................... 6-20
[ 34 ] 0s Overspeed protection ..................................................................................................... 6-21
[ 35 ] 0un Overvoltage ................................................................................................................. 6-21
[ 36 ] pbf Charge circuit fault ....................................................................................................... 6-22
[ 37 ] pg PG wire break ................................................................................................................ 6-22
6.4 If the “Light Alarm” Indication (
l-al
) Appears on the LED Monitor ................................................ 6-23
6.5 When Codes Other Than Alarm Codes and Light Alarm Indication (
l-al
) are Displayed ............. 6-24
6.5.1 Abnormal motor operation ........................................................................................................... 6-24
[ 1 ] The motor does not rotate ...................................................................................................... 6-24
[ 2 ] The motor rotates, but the speed does not increase .............................................................. 6-26
[ 3 ] The motor runs in the opposite direction to the command ...................................................... 6-27
[ 4 ] Speed fluctuation or current oscillation (e.g., hunting) occurs during running
at constant speed ................................................................................................................... 6-28
[ 5 ] Unpleasant noises are emitted from motor or noises fluctuate ............................................... 6-29
[ 6 ] Motor is not accelerated or decelerated according to set-up acceleration
or deceleration times .............................................................................................................. 6-29
[ 7 ] The motor does not restart even after the power recovers from a momentary power failure .. 6-30
[ 8 ] Motor generates heat abnormally ........................................................................................... 6-30