Fuji Electric FRENIC-Ace series - Page 7

v
4.10 Selecting a Frequency Command Source ....................................................................................... 4-30
4.10.1 Setting up a frequency command from the keypad .................................................................... 4-30
4.10.2 Setting up a frequency command with an external potentiometer .............................................. 4-30
4.10.3 Setting up a frequency command with multistep frequency selection ........................................ 4-31
4.11 Selecting a Run Command Source ................................................................................................. 4-32
4.11.1 Setting up a run command from the keypad .............................................................................. 4-32
4.11.2 Setting up a run command with digital input signals (terminals [FWD] and [REV]) .................... 4-32
FUNCTION CODES Chapter 5
5.1 Function Codes Overview .................................................................................................................. 5-1
5.2 Function Codes Table ........................................................................................................................ 5-2
5.2.1 Supplementary note ...................................................................................................................... 5-2
5.2.2 Function codes table ..................................................................................................................... 5-4
5.2.3 Factory default value per applicable electric motor capacitance ................................................. 5-36
5.2.4 Motor constants ........................................................................................................................... 5-37
[ 1 ] When Fuji standard motor 8-series, or other motors are selected by motor selection
(Function code P99/ A39 = 0 or 4) .......................................................................................... 5-37
[ 2 ] When HP rating motor is selected by motor selection (Function code P99/A39 = 1) .............. 5-41
5.3 Description of Function Codes ......................................................................................................... 5-45
5.3.1 F codes (Basic functions) ............................................................................................................ 5-45
[ 1 ] Frequency setting by keypad (F01 = 0 (Factory default state), 8) ........................................... 5-47
[ 2 ] Setting up a reference frequency using analog input (F01 = 1 to 3, 5) ................................... 5-48
[ 3 ] Frequency setting by digital input signal “UP”/“DOWN” (F01=7) ............................................ 5-54
[ 4 ] Frequency setting using digital inputs (option DIO interface card) (F01 = 11) ........................ 5-55
[ 5 ] Frequency setting using pulse train input (F01 = 12) .............................................................. 5-55
5.3.2 E codes (Extension terminal functions) ..................................................................................... 5-100
5.3.3 C codes (Control functions) ....................................................................................................... 5-139
5.3.4 P codes (Motor 1 parameters) ................................................................................................... 5-148
5.3.5 H codes (High performance functions) ...................................................................................... 5-155
[ 1 ] Measuring the capacitance of DC link bus capacitor in comparison with initial one
at shipment ........................................................................................................................... 5-171
[ 2 ] Measuring the capacitance of DC link bus capacitor under ordinary operating conditions
at power shutdown................................................................................................................ 5-172
5.3.6 A codes (Motor 2 parameters) ................................................................................................... 5-193
5.3.7 b, r codes (Speed control 3 and 4 parameters) ......................................................................... 5-196
5.3.8 J codes (Applied functions) ....................................................................................................... 5-197
[ 1 ] PID command with the / keys on the keypad (J02 = 0, factory default) ..................... 5-198
[ 2 ] PID command by analog inputs (J02 = 1) ............................................................................. 5-199
[ 3 ] PID command with UP/DOWN control (J02 = 3) .................................................................. 5-201
[ 4 ] PID command via communications link (J02 = 4) ................................................................. 5-201
[ 5 ] Overload stop function .......................................................................................................... 5-213
[ 6 ] Brake control signal .............................................................................................................. 5-214
[ 7 ] Positioning control with pulse counter ................................................................................... 5-217
[ 8 ] Servo lock ............................................................................................................................. 5-226
5.3.9 d codes (Applied functions 2) .................................................................................................... 5-228
[ 1 ] Speed control ....................................................................................................................... 5-228
[ 2 ] Master-follower operation ..................................................................................................... 5-238
5.3.10 U codes (Customizable logic operation) ................................................................................... 5-248
5.3.11 U1 codes (Customizable logic operation) ................................................................................. 5-273
5.3.12 y codes (Link functions) ........................................................................................................... 5-277
TROUBLESHOOTING Chapter 6
6.1 Protective Function ............................................................................................................................ 6-1
6.2 Before Proceeding with Troubleshooting ........................................................................................... 6-2