SEQ P7: ARP/DT (Arpeggiator/DrumTrack) Synchronizing the Drum Track function
147
Synchronizing the Drum Track function
The Trigger “Sync” parameter
The trigger timing of a drum track will depend on the
setting of its Trigger Sync parameter.
On (checked): The trigger timing will be quantized to the
nearest beat relative to the base tempo.
Off (unchecked): If Trigger Mode is Start Immediately,
triggering will occur at the moment you press the DRUM
TRACK button. If this is set to Wait KBD Trig, triggering will
occur at the moment you play the keyboard.
Synchronizing the drum track with the arpeggia-
tor function, Sequencer mode songs, patterns,
and RPPR performance
If you want the Drum Track pattern to play or be recorded in
synchronization with the currently‐operating arpeggiator
function, currently‐playing song, pattern, or RPPR
performance, turn Trigger Sync on.
Trigger Sync Off: If the Trigger Mode setting is Start
Immediately, the Drum Track pattern will be triggered the
moment you press the DRUM TRACK button. If this is set to
Wait KBD Trig, the Drum Track pattern will be triggered the
moment you play the keyboard. It will not synchronize to
the currently‐operating arpeggiator function or to the
currently‐playing song, pattern, or RPPR.
Trigger Sync On: Triggering will synchronize to the
currently‐playing song, pattern or RPPR performance at the
beginning of the next measure. Triggering will synchronize
to the currently‐operating arpeggiator (in Sequencer mode if
the song or pattern is stopped) on the next beat.
Note: If you want to synchronize the arpeggiator to the
currently‐running Drum Track function, set the Key Sync
parameter (Prog/Combi/Seq P7).
Note: If you want to synchronize the RPPR pattern
performance to the currently‐running Drum Track function,
set the Sync parameter (Seq P10: Pattern/RPPR– RPPR Setup
page) to Beat or Measure.
Synchronization with song stop
Synchronization with a song in Sequencer mode
• When you press the START/STOP ( ) button, the
Drum Track function and the sequencer will stop.
• If you want the Drum Track function to start
simultaneously with the beginning of recording, press the
DRUM TRACK button during the pre‐count before
recording (if the Trigger Mode is set to Start Immediately)
or play the keyboard (if Trigger Mode is Wait KBD Trig).
The Drum Tracks will not be triggered immediately, but
will be triggered in synchronization with the sequencer
the moment recording starts.
Slave operation
The KROME’s sequencer can be made to run in
synchronization with the clock and realtime commands
received from an external sequencer. Connect the MIDI OUT
of your external MIDI device to the KROME's MIDI IN, or
connect the KROME's USB port to your computer's USB
port.
Connect the KROME’s MIDI IN to your external MIDI
device’s MIDI OUT, or connect the KROME’s USB connector
to your computer’s USB port.
Set MIDI Clock (Global, see p.199) to External MIDI or
External USB. The KROME will synchronize to MIDI Clock
and realtime command messages it receives from the
connected MIDI device.
Note: If the KROME is set to MIDI Clock= Auto, it will also
synchronize to the external MIDI device in the same way if
MIDI realtime clock messages are being received from the
external device.
Synchronization to MIDI clock
The arpeggiator will synchronize to the tempo coming from
an external MIDI clock source.
Synchronization with MIDI realtime commands
In Sequencer mode, the KROME will respond to Song Start,
Continue, and Stop messages that it receives just as it does
when using the front panel START/STOP ( ) button
to control song playback and recording. The arpeggiator
also will be controlled in the same way. (See
“Synchronization with song stop” above)
Master operation
The KROME sequencer's clock data and start/stop
operations can be used to synchronize and control an
external sequencer.
Connect the KROME’s MIDI OUT to your external MIDI
device’s MIDI IN, or connect the KROME’s USB connector to
your computer’s USB port.
Set MIDI Clock (Global 1–1a) to Internal. The connected
external MIDI device will synchronize to the KROME’s
MIDI Clock.
Note: The same applies if MIDI Clock=Auto and MIDI
Clock messages are being transmitted. For details, please see
“MIDI Clock (MIDI Clock Source)” on page 199.
Synchronization via MIDI clock
The connected external MIDI device will synchronize to the
MIDI clock of the KROME.
Sync: O
Sync: Beat
Sync: Measure
Key 1 on
Song
Key 2 on
Key 1 o
Sync settings
Patterns 1 and 2 are set to
Mode=Manual, and have
identical Sync settings
Pattern 1
Pattern 2
Pattern 1
Pattern 2
Pattern 1
Pattern 2
To Next Page
Loading...
