Kyocera FS-C8600DN Service Manual

2MN/2N1
2-2-5
18. MP paper sensor (MPPS) ..................... Detects the presence of paper (MP tray).
19. MP lift sensor 1 (MPLS1) ...................... Detects activation of upper limit of the MP plate.
20. MP lift sensor 2 (MPLS2) ...................... Detects activation of lower limit of the MP plate.
21. MP paper length switch (MPPLSW)...... Detects the length of paper (MP tray).
22. MP paper width switch (MPPWSW)...... Detects the width of paper (MP tray).
23. MP tray switch (MPTSW)...................... Detects the MP tray extension is extend.
24. MP feed sensor (MPFS) ....................... Detects a paper misfeed in the MP paper feed section.
25. Middle sensor (MS)............................... Detects a paper misfeed in the paper conveying section.
26. Regist deflection sensor (RDS)............. Detects the deflection in the paper.
27. Registration sensor (RS)....................... Controls the secondary paper feed start timing.
28. Screw sensor K (SRS-K) ...................... Controls the toner replenishing for the toner container K.
29. Screw sensor M (SRS-M) ..................... Controls the toner replenishing for the toner container M.
30. Screw sensor C (SRS-C) ...................... Controls the toner replenishing for the toner container C.
31. Screw sensor Y (SRS-Y) ...................... Controls the toner replenishing for the toner container Y.
32. Toner sensor K (TS-K) .......................... Detects the toner density in the developer unit K.
33. Toner sensor M (TS-M) ......................... Detects the toner density in the developer unit M.
34. Toner sensor C (TS-C).......................... Detects the toner density in the developer unit C.
35. Toner sensor Y (TS-Y) .......................... Detects the toner density in the developer unit Y.
36. ID sensor 1 (IDS1) ................................ Measures image density for color calibration.
37. ID sensor 2 (IDS2) ................................ Measures image density for color calibration.
38. Color release sensor (CRS).................. Detects separation of primary transfer rollers M, C, and Y.
39. Transfer belt sensor (TRBLS) ............... Detects positioning of transfer belt rotation.
40. Transfer skew sensor (TRSS)............... Detects skew of transfer belt center position.
41. Transfer edge sensor (TRES) ............... Detects edge position of the transfer belt.
42. Transfer release sensor (TRRS) ........... Detects separation of secondary transfer roller.
43. Loop sensor (LPS) ................................ Detects a paper misfeed. Controls the fuser motor by detecting
deflection in the paper.
44. Fuser belt sensor (FUBLS) ................... Detects positioning of fuser belt rotation.
45. Fuser release sensor (FURS) ............... Detects fuser pressure release setting (envelope mode).
46. Fuser thermistor 1 (FTH1) .................... Detects the heat roller (fuser belt) temperature.
47. Fuser thermistor 2 (FTH2) .................... Detects the heat roller (fuser belt) temperature.
48. Fuser thermistor 3 (FTH3) .................... Detects the heat roller (fuser belt) temperature.
49. Fuser thermistor 4 (FTH4) .................... Detects the press roller temperature.
50. Fuser eject sensor (FUES) ................... Detects a paper misfeed in the fuser section.
51. Eject full sensor 1 (EFS1) ..................... Detects a paper misfeed in the eject section. Detects when the
main tray is full.
52. Eject full sensor 2 (EFS2) ..................... Detects a paper misfeed in the eject section. Detects when the
sub tray is full.
53. Switchback sensor (SBS) ..................... Detects a paper misfeed in the eject and switchback sections.
54. Duplex sensor 1 (DUS1) ....................... Detects a paper misfeed in the duplex section.
55. Duplex sensor 2 (DUS2) ....................... Detects a paper misfeed in the duplex section.
56. Duplex cover switch (DUCSW) ............. Detects the opening and closing of the duplex cover.
57. Waste toner sensor 1 (WTS1)............... Detects when the waste toner box is full.
58. Waste toner sensor 2 (WTS2)............... Detects when the waste toner box is near end.
59. Paper conveying unit switch
(PCUSW) .............................................. Detects the opening and closing of the paper conveying unit.
60. Paper conveying cover switch
(DUCSW) .............................................. Detects the opening and closing of the paper conveying cover.
61. Outer temperature sensor
(OTEMS)............................................... Detects the outside temperature and humidity.

Kyocera FS-C8600DN Specifications

General

Color	Yes
Print technology	Laser
Maximum resolution	9600 x 600 DPI
Duplex printing mode	Auto
Time to first page (black, normal)	5.4 s
Time to first page (color, normal)	6.6 s
Print speed (black, normal quality, A3)	22 ppm
Print speed (black, normal quality, A4/US Letter)	45 ppm
Printing colors	Black, Cyan, Magenta, Yellow
Maximum duty cycle	- pages per month
Number of print cartridges	-
Page description languages	Diablo 630, Microsoft XPS, PCL 5c, PCL 6, PCL XL, PDF 1.7
Paper input type	Cassette, Paper tray
Total input capacity	650 sheets
Total output capacity	500 sheets
Maximum input capacity	7650 sheets
Multi-Purpose tray input capacity	150 sheets
Paper tray media types	Banner, Plain paper, Thick paper
ISO A-series sizes (A0...A9)	A3, A4, A5
Maximum ISO A-series paper size	A3
Wi-Fi	No
Standard interfaces	Ethernet, USB 2.0
Optional connectivity	Ethernet
Memory slots	2
Storage media	HDD
Processor family	PowerPC
Compatible memory cards	CF
Maximum internal memory	2048 MB
Internal storage capacity	160 GB
Sound power level (standby)	33.9 dB
Sound pressure level (printing)	52.3 dB
Certification	GS, TüV, CE
Product color	Black
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	1140 W
Power consumption (standby)	170 W
Power consumption (printing)	1000 W
Power consumption (PowerSave)	15 W
Sustainability certificates	ENERGY STAR
Harmonized System (HS) code	84433210

Weight and Dimensions

Depth	787 mm
Width	672 mm
Height	744 mm