© 2013 MIMAKI ENGINEERING CO.,LTD.
7.1.3 P.1
1
2
3
4
5
6
7
8
R.2.0
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Warning Messages
Model UJF-3042/FX Issued 2010.08.27
Revised
2011.09.30
F/W ver
1.80 / 1.00
Remark
2.0
7.1.3 List of Warning Messages
List of Warning Messages (1/2)
No. Message Cause Corrective Measures
1
<LOCAL> NO CARTRDG
MCYKWR
No cartridge (Cartridge is not
installed)
(When the message is still displayed even after a Ink Cartridge is
charged;)
1. Execute and confirm [#TEST]->[SENSOR TEST]->
[INK1](The number meets the cartridge No.).
2. Check the peripheral and the assembly of the Presence Sensor.
3. Check the connection of the Presence Sensor and the End Sensor
4. .Replace the Cartridge with a new one
5. Replace the Presence/Near End Sensor with a new one.
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
7. Replace the Main PCB with a new one. (Refer to 3.3.1)
2
<LOCAL> INK NEAREND
MCYKWR
Ink near end (A small amount
of ink left)
(When the message is still displayed even after a new Ink Cartridge or an
empty Ink Cartridge is charged;)
1. Execute and confirm [#TEST]->[SENSOR TEST]->
[INK NEND1](The number meets the cartridge No.).
2. Check the peripheral and the assembly of the End Sensor.
3. Check the connection of the Presence Sensor and the Near End
Sensor.
4. Replace the Cartridge with a new one
5. Replace the Presence/Near End Sensor with a new one.
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
7. Replace the Main PCB with a new one. (Refer to 3.3.1)
3
<LOCAL> INK END
MCYKWR
Ink end (No ink left) (If this message appears when a new cartridge or a cartridge with
enough ink is set)
1. Execute and confirm [#TEST]->[SENSOR TEST]->
[INK NEND1](The number meets the cartridge No.).
2. Check the peripheral and the assembly of the End Sensor.
3. Check the connection of the Presence Sensor and the End Sensor.
4. Replace the Cartridge with a new one.
5. Replace the Presence / Near End Sensor with a new one.
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
7. Replace the Main PCB with a new one. (Refer to 3.3.1)
4
<LOCAL> Expiration
MCYKWR
Some ink cartridges are
expired.
1. 1. Check the expiration date of the ink.
(If this message appears when a correct cartridge is set)
2. Check the assembly of the ID Contact PCB and the shape of the
contact plate, and execute the cleaning.
3. Check the connection of the ID Contact PCB.
4. Replace the Cartridge with a new one.
5. Replace the ID Contact PCB Assy. with a new one. (Refer to 3.3.3)
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
5
<LOCAL> INK TYPE
MCYKWR
Type of inserted Ink Cartridge
is different.
1. Check the type of the ink cartridge.
Execute the followings if the type of the ink cartridge is correct.
2. Check the assembly of the ID Contact PCB and the shape of the
contact plate, and execute the cleaning.
3. Check the connection of the ID Contact PCB.
4. Replace the Cartridge with a new one
5. Replace the ID Contact PCB Assy. with a new one. (Refer to 3.3.3)
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
6
<LOCAL> ColorofINK
MCYKWR
The color of Ink Cartridge
inserted is different from the
color to be set.
7
<LOCAL> NON-ORIGNL
MCYKWR
Non-MIMAKI genuine Ink
Cartridge charged
8
<LOCAL> WRONG INK IC
MCYKWR
IC chip of Ink Cartridge
unreadable properly
To Next Page
Loading...
