MIMAKI UJF-3042 - Page 213

© 2013 MIMAKI ENGINEERING CO.,LTD.
7.1.3 P.2
7.1.3 List of Warning Messages
1
2
3
4
5
6
7
8
9 <LOCAL>
!WORK High
The Work Area Sensor
detected an obstacle that can
hit the head.
Lower the table until this warning disappears.
If this warning does not disappear when the table is lowered to the
bottom.
1. Execute and confirm [#TEST]->[SENSOR TEST] ->[
HEIGHT-
SES ].
2. Readjust the Work Area Sensor.
3. Readjust the height of the carriage.
4. Check the Connectors of Work Area Sensor connected on the PCB
5. Replace the Work Area Sensor with a new one.
6. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
7. Replace the Pump 3 PCB with a new one.
(Refer to 6.4.6)
10 <LOCAL>
WATER LACK
Water in the cooling water
buffer tank is low.
1. Check amount of water in the cooling water buffer tank, and replace
the Nonfreezing fluid mixture water if lacking.
2. If water decreases quickly, check water leakage from the cooling
water path (a tube or a radiator).
•Execute [#TEST SENSOR TEST]->[CoolFloat] to check the sensor
operation.
3. Check the assembly of the Float Sensor and the connector
connection.
4. Replace the Float Sensor and the Cable with a new one.
5. Replace the SL-Relay PCB with a new one.
(Refer to 3.3.2)
11
<LOCAL>
!WS INKTANK CHK
A great deal of ink is in the
Wast ink tank
1. Check the Wast ink tank.
2. Select [FUNCTION MAINTENANCE]->[STATION]-
>[MENT:WASTE TANK] and dispose of ink in the Wast ink tank.
12
<LOCAL>
WIPER BOTTLE
A great deal of ink is in the
Wiper Bottle.
1. Check the Wiper Bottle.
2. Select [FUNCTION MAINTENANCE]->[STATION]-
>[MENT:WIPER BOTTLE] and dispose of ink in the Wiper Bot-
tle.
13
<LOCAL>
CLEANING WIPER
Wiping times exceeding the
specified number.
1. Execute [FUNCTION MAINTENANCE]->[STATION]-
>[MENT:WIPER CLEANING] to clean the wiper.
14
<LOCAL>
!CHECK FILTER
A filter may be stained.
1. Check the filter.
1. Execute [FUNCTION MAINTENANCE]->[STATION]-
>[MENT:CHECK FILTER] to replace the filter..
15
<LOCAL>
CAP CLEANING
Warning for cleaning around cap
(Flushing times on the cap
exceeded the specified
number.)
1. Execute [STATION] -> [MENT: CARRIAGE OUT] to clean the cap.
16 <LOCAL>
Case Weight
[CASE WEIGHT] of 600ml
CARTRIDGE was not set.
1. Set [CASE WEIGHT] from [MACHINE SET] -> [600ml CARTRIDGE].
17 <LOCAL>
INK LVL LOW
The remaining amount of ink
became less.
1. Enter the cartridge weight from [CART WEIGHT] menu of [SET UP].
18 <LOCAL>
INK LVL END
Remaining amount of ink became
none.
 If ink remains, enter the cartridge weight from "CART WEIGHT" menu of
"SET UP".
• If ink does not remain, replace it with a new cartridge.
19 <LOCAL>
!CHECK LED UV LEVEL
1. Check the illuminance of the LED UV lamp. If it is less than the specified
value, replace the lamp.
20 <LOCAL>
Preservation Failure
Remaining amount of ink was
failed to be written.
1. Pull the cartridge out and then insert it to write it again.
2. If the error cannot be solved, replace it with a new cartridge.
21 <LOCAL>
Cartridge Weight
The cartridge weight was not
entered.
1. Enter the cartridge weight.
 List of Warning Messages (2/2)
No. Message Cause Corrective Measures
R.2.0
Maintenance Manual > Troubleshooting > Details on Errors and Malfunctions > List of Warning Messages
Model UJF-3042/FX Issued 2010.08.27 Revised 2011.09.30 F/W ver 1.80 / 1.00 Remark
2.0
Rev.