What does RTD mean on my Mold-Masters M2 Controller and what to do?
The RTD error on your Mold-Masters Controller indicates that the RTD monitor cannot see an input, meaning the RTD is open circuit. Check the RTD and its wiring for a broken connection.
What does N/Z mean on my Mold-Masters M2 and how do I fix it?
The N/Z error on your Mold-Masters Controller means that a control card is not responding to the console. Check the communication lead between the console and the controller cabinet.
What does LINK mean on my Mold-Masters M2 Controller and how to solve it?
The LINK error on your Mold-Masters Controller means the console is switched to a remote controller with a network link, but it cannot establish communication with the remote unit. Check that the network link is good and/or the remote controller is still switched on and available.
General| Brand | Mold-Masters |
|---|---|
| Model | M2 |
| Category | Controller |
| Language | English |
Explanation of WARNING and CAUTION symbols and their meanings.
Recommended environments and ambient condition limits for the equipment.
Importance of correct wiring and potential errors.
Procedures for switching the controller on and off.
Recommended steps to shut down the heating load, console, and controller.
Step-by-step guide to setting temperatures for one or more zones.
Initial step to detect available cards and populate the Setup page.
Allocating duties to detected cards and fine-tuning tool parameters.
Detailed steps for creating a new tool using the [Detect] command.
List and descriptions of detected cards (Z6, Z4, Z2, AI8, D12, WT3, WT4, IO3/4, IO5, DO32, SVG).
Steps to configure detected cards by selecting Zone Type.
Steps to select zones, parameters, and set values.
Detailed functions, descriptions, and setting limits for tool parameters.
Accessing and configuring Tool and System settings.
Parameters affecting the selected tool, requiring Accept and Save.
General system settings applicable regardless of the loaded tool.
Steps for selecting zones to set operating parameters.
How to select the first and last zone using the [Range] option.
Procedure for setting probe and manifold temperatures using Auto or manual input.
Steps to set body and tip temperatures for spear control.
Procedure for setting values for cavities, water flows, and chillers.
Steps to save tool settings to the Tool Store page.
Steps for preparing and loading images for EasyView.
Explanation of user access levels (Operator, Maintenance, Supervisor).
Steps to log in as admin and set up user accounts.
Adding and configuring new users with passwords and security levels.
Reviewing, editing, and deleting current user accounts.
Setting function permissions based on user job titles.
Automatic leakage detection system and its modes (Auto, Manual, Off).
Setting up auto leakage actions and understanding display indicators.
Procedure for logging into the system using a password.
Description of available operation modes (RUN, STOP, STANDBY, STARTUP, SHUTDOWN, BOOST, PURGE).
Step-by-step instructions for changing zone temperatures via the Display page.
How to change working modes (Manual, Auto, Slaved) for zones.
Steps to change zone temperatures using the EasyView page.
Steps to change working modes for zones using the EasyView page.
Explanation of Mechanical and Chemical purge modes.
Setting parameters for recommended cycles, purge material, cycles, and soak time.
Recording and displaying temperature history for zones.
Viewing zone temperature and power history over 5 or 30 minutes.
Viewing zone temperature and power history over the last 24 hours.
Steps to create a new tool with alternative settings.
Steps to edit the name of an existing tool.
How to load tool settings from the local console memory.
Using an IO5 card to remotely select different tools.
Options for saving tool settings, including overwriting existing ones.
Saving new satisfactory settings back into the same tool store.
Creating a new store to save modified settings while retaining old ones.
Procedure for deleting a tool, with a warning about data recovery.
Saving tool settings to external media for recovery or transfer.
Steps to back up all tools to USB memory.
Steps to back up a single selected tool setting to USB memory.
Restoring tool settings from selected banks or slots.
Steps to restore all tools from USB memory.
Steps to restore a single tool from USB memory.
Saving images and text to USB memory and loading them into the console.
Saving images and associated text to USB memory.
Using the IO5 card for remote tool loading via connectors.
Sequence for remotely loading tools with control and feedback.
Printing pages to a file on a USB memory stick in various formats.
Extracting zone performance data as a zipped CSV file.
Overview of diagnostic tests: Power Test and Full System Test.
Procedures for running self-diagnosis tests.
Selecting specific zones for self-diagnosis.
List of error messages and their possible causes for failed tests.
Steps to upgrade console software via USB.
Table of error messages, causes, and actions.
Steps to set and calibrate screw sensor for gate control.
Setting gate open and close triggers and values.
To Next Page
