Oki MC860 Maintenance Manual

43967002TH Rev.1
124 /
Oki Data CONFIDENTIAL
3. Installation
Network Menu
The shaded portion shows the default setup value when shipped from the factory.
Item Contents
Network
Setup
TCP/IP Disable
Enable
It sets valid/invalid of TCP/IP protocol.
IP Version IPv4
IPv4 + IPv6
It sets IP version number to be used.
It is not displayed when TCP/IP is invalid.
NetBEUI Disable
Enable
It sets valid/invalid of NETBEUI protocol.
NetBIOS over TCP Disable
Enable
It sets Enable/Disable of NetBIOS over
TCP protocol.
This menu is not displayed when TCP/IP is
invalid, or if IP version number is IPv6.
NetWare Disable
Enable
It sets Enable/Disable of NetWare protocol.
EtherTalk Disable
Enable
It sets Enable/Disable of EtherTalk
protocol.
Frame type Auto
802.2
802.3
ETHERNET II
SNAP
It sets frame type.
* It is not displayed when NetWare is
Disable.
IP Address Setting Auto
Manual
It sets method of setting up IP address..
This menu is not displayed when TCP/IP is
invalid, or if IP version number is IPv6.
IPv4 address . . .
100
It sets IP address.
This menu is not displayed when TCP/IP is
invalid, or if IP version number is IPv6.
The shaded portion shows the default setup value when shipped from the factory.
Item Contents
Network
setup
Subnet Mask . . . It sets subnet mask.
This menu is not displayed when TCP/IP is
invalid, or if IP version number is IPv6.
Gateway Address . . . Set gateway address.
This menu is not displayed when TCP/IP is
invalid, or if IP version number is IPv6.
Web Disable
Enable
Set Enable/Disable of access from Web
browser.
This menu is not displayed when TCP/IP is
invalid.
Telnet Disable
Enable
Set Enable/Disable of access from
TELNET.
This menu is not displayed when TCP/IP is
Disable.
FTP Disable
Enable
Set Enable/Disable of access from FTP.
This menu is not displayed when TCP/IP is
Disable.
IPSec Disable
Enable
It is displayed and change to Disable is
possible only when IP Sec is set to valid.
Implement setup from Web browser to
make IPSec valid.
SNMP Disable
Enable
Set valid/invalid of access from SNMP.
This menu is not displayed when TCP/IP is
invalid and NETWARE is invalid.

Oki MC860 Specifications

Printing Specifications

print speed color	26 ppm
print speed black & white	33 ppm
time to first page color	10 seconds
time to first page black & white	9.5 seconds
print resolution	1200 x 600 dpi
processor	500 MHz PowerPC CPU
duty cycle	75, 000 prints per month

Copying Specifications

copy speed color	26 cpm
copy speed black & white	33 cpm
first copy out color	14.5 seconds
first copy out black & white	13 seconds
copy resolution	600 x 600 dpi

Scanning Specifications

scan type	Color and black & white
max scan area	11" x 17"
scan speed black & white	33 spm
scan speed color	26 spm
scan resolution	600 dpi

Fax Specifications

fax modem	33.6 Kbps Super G3
transmission speed	2 seconds/page
fax resolution	600 x 600 dpi
speed dial locations	500 locations
broadcast transmission locations	530 locations

Power and Acoustic Noise

power consumption peak	1, 300W
power consumption standby	160W Avg.
power save mode	≤25W
acoustic noise operating	54dB
acoustic noise standby	≤37dB

System Memory

standard imaging RAM	512 MB
max imaging RAM	768 MB
hard disk drive	40 GB

Weight and Dimensions

1-tray configuration dimensions	22.2" x 25.9" x 26.3"
2-tray configuration dimensions	33.3" x 30.2" x 44.5"
weight 1-tray configuration	149.9 lb
weight 2-tray configuration	200.6 lb
weight 3-tray configuration	211.6 lb