Schweitzer Engineering Laboratories SEL-311C - List of Tables

Date Code 20060320 Instruction Manual SEL-311C Relay
List of Tables
Table 1.1 SEL-311C Models.................................................................................................................. 1.2
Table 2.1 Communications Cables to Connect the SEL-311C to Other Devices ................................ 2.15
Table 2.2 Output Contact Jumpers and Corresponding Output Contacts ............................................ 2.23
Table 2.3 Move Jumper JMP 23 to Select Extra Alarm....................................................................... 2.24
Table 2.4 Password and Breaker Jumper Operation ............................................................................ 2.24
Table 2.5 EIA-232 Serial Port Voltage Jumper Positions for Standard Relay Shipments ................... 2.25
Table 3.1 Phase Distance Calculations................................................................................................... 3.2
Table 3.2 Distance Elements Settings .................................................................................................... 3.6
Table 3.3 Ground Distance Elements Settings..................................................................................... 3.10
Table 3.4 Zone 1 Settings..................................................................................................................... 3.19
Table 3.5 Zone Timing Settings ........................................................................................................... 3.20
Table 3.6 Out-of-Step Settings............................................................................................................. 3.22
Table 3.7 OOS Relay Word Bits .......................................................................................................... 3.23
Table 3.8 Available Phase Time-Overcurrent Elements....................................................................... 3.33
Table 3.9 Phase Time-Overcurrent Element (Maximum Phase) Settings............................................ 3.33
Table 3.10 Phase Time-Overcurrent Element (Maximum Phase) Logic Outputs.................................. 3.34
Table 3.11 Residual Ground Time-Overcurrent Element Settings......................................................... 3.37
Table 3.12 Negative-Sequence Time-Overcurrent Element Settings..................................................... 3.38
Table 3.13 Voltage Values Used by Voltage Elements........................................................................... 3.40
Table 3.14 Voltage Elements Settings and Settings Ranges .................................................................. 3.40
Table 3.15 Synchronism Check Elements Settings and Settings Ranges .............................................. 3.45
Table 3.16 Frequency Elements Settings and Settings Ranges.............................................................. 3.57
Table 4.1 Load-Encroachment Logic Settings Ranges .......................................................................... 4.6
Table 4.2 Elements Controlled by Zone/Level Direction Settings (Corresponding
Overcurrent and Directional Element Figure Numbers in Parentheses)............................. 4.21
Table 4.3 First Entry in ORDER Setting if Ground Quadrilateral Distance Elements Are Used........ 4.23
Table 4.4 Torque Control Settings and Elements................................................................................. 4.28
Table 5.1 SEL-311C Front-Panel Target LED Definitions .................................................................. 5.31
Table 6.1 Relay Word Bit and Front-Panel Correspondence to Reclosing Relay States ..................... 6.12
Table 6.2 Reclosing Relay Timer Settings and Setting Ranges ........................................................... 6.14
Table 6.3 Relay Word Bits Used to Monitor Open Interval and Reset Timing.................................... 6.16
Table 6.4 Shot Counter Correspondence to Relay Word Bits and Open Interval Times ..................... 6.17
Table 6.5 Reclosing Relay SEL
OGIC Control Equation Settings Example.......................................... 6.17
Table 6.6 Open Interval Time Settings Example ................................................................................. 6.22
Table 7.1 Correspondence Between Local Control Switch Positions and Label Settings ..................... 7.7
Table 7.2 Correspondence Between Local Control Switch Types and Required Label Settings........... 7.8
Table 7.3 Local Bits LB3 and LB4 Used for Manual Trip and Close Functions................................... 7.9
Table 7.4 Definitions for Active Setting Group Indication Relay Word Bits SG1–SG6 ..................... 7.19
Table 7.5 Definitions for Active Setting Group Switching
SEL
OGIC Control Equation Settings SS1–SS6 ................................................................... 7.19
Table 7.6 SEL
OGIC Control Equation Settings for Switching
Active Setting Group Between Setting Groups 1 and 4...................................................... 7.21
Table 7.7 Active Setting Group Switching Input Logic....................................................................... 7.23
Table 7.8 SEL
OGIC Control Equation Settings for Rotating
Selector Switch Active Setting Group Switching ............................................................... 7.24
Table 7.9 Settings for Displaying Time-Overcurrent Elements ........................................................... 7.42
Table 7.10 Relay Setting Variables ........................................................................................................ 7.43
Table 7.11 Mnemonic Settings for Metering on the Rotating Default Display ..................................... 7.44
Table 7.12 Settings for Displaying Metering Values Example .............................................................. 7.46
Table 7.13 Mnemonic Settings for Self-Check Status on the Rotating Default Display ....................... 7.47
Table 7.14 Settings for Displaying Breaker Monitor Outputs Example ................................................ 7.47
Table 8.1 Breaker Maintenance Information for an Example Circuit Breaker ...................................... 8.2
Table 8.2 Breaker Monitor Settings and Settings Ranges...................................................................... 8.4
Table 8.3 Breaker Monitor Output Relay Word Bits ........................................................................... 8.12