D.13
Date Code 20060320 Instruction Manual SEL-311C Relay
Configuration, Fast Meter, and Fast Operate Commands
Message Definitions
The DNA message is:
<STX>
"EN","TRP","TIME","COMM","SOTF","RCRS","RCLO","51","0B70"
"A","B","C","G","ZONE1","ZONE2","ZONE3","ZONE4","0A47"
"M1P","M1PT","Z1G","Z1GT","M2P","M2PT","Z2G","Z2GT","0B54"
"Z1T","Z2T","50P1","67P1","67P1T","50G1","67G1","67G1T","0B50"
"51G","51GT","51GR","LOP","ILOP","ZLOAD","ZLOUT","ZLIN","0CA1"
"LB1","LB2","LB3","LB4","LB5","LB6","LB7","LB8","0994"
"LB9","LB10","LB11","LB12","LB13","LB14","LB15","LB16","0AE5"
"RB1","RB2","RB3","RB4","RB5","RB6","RB7","RB8","09C4"
"RB9","RB10","RB11","RB12","RB13","RB14","RB15","RB16","0B15"
"LT1","LT2","LT3","LT4","LT5","LT6","LT7","LT8","0A24"
"LT9","LT10","LT11","LT12","LT13","LT14","LT15","LT16","0B75"
"SV1","SV2","SV3","SV4","SV1T","SV2T","SV3T","SV4T","0BAC"
"SV5","SV6","SV7","SV8","SV5T","SV6T","SV7T","SV8T","0BCC"
"SV9","SV10","SV11","SV12","SV9T","SV10T","SV11T","SV12T","0CD6"
"SV13","SV14","SV15","SV16","SV13T","SV14T","SV15T","SV16T","0D44"
"MAB1","MBC1","MCA1","MAB2","MBC2","MCA2","CVTBL","SOTFT","0C9A"
"MAG1","MBG1","MCG1","MAG2","MBG2","MCG2","DCHI","DCLO","0BE7"
"BCW","BCWA","BCWB","BCWC","FIDEN","FSA","FSB","FSC","0BAD"
"SG1","SG2","SG3","SG4","SG5","SG6","OC","CC","0969"
"CLOSE","CF","TRGTR","52A","3PO","SOTFE","VPOLV","50L","0C55"
"PDEM","GDEM","QDEM","TRIP","50QF","50QR","50GF","50GR","0C1D"
"32QF","32QR","32GF","32GR","32VE","32QGE","32IE","32QE","0BA4"
"F32I","R32I","F32Q","R32Q","F32QG","R32QG","F32V","R32V","0C18"
"*","*","IN106","IN105","IN104","IN103","IN102","IN101","0AD9"
"ALARM","OUT107","OUT106","OUT105","OUT104","OUT103","OUT102","OUT101","0FC8"
"M3P","M3PT","Z3G","Z3GT","M4P","M4PT","Z4G","Z4GT","0B64"
"Z3T","Z4T","50P2","67P2","67P2T","50P3","67P3","67P3T","0B78"
"50G2","67G2","67G2T","50G3","67G3","67G3T","*","*","09D3"
"51P","51PT","51PR","Z1X","59VA","MAB3","MBC3","MCA3","0B3C"
"MAG3","MBG3","MCG3","27S","59S","*","59VP","59VS","0A6D"
"SF","25A1","25A2","RCSF","OPTMN","RSTMN","*","*","0A70"
"79RS","79CY","79LO","SH0","SH1","SH2","SH3","SH4","0AAD"
"MAB4","MBC4","MCA4","MAG4","MBG4","MCG4","*","*","0A01"
"XAG1","XBG1","XCG1","XAG2","XBG2","XCG2","XAG3","XBG3","0C16"
"XCG3","XAG4","XBG4","XCG4","OSTI","OSTO","OST","50ABC","0C79"
"X5ABC","X6ABC","OSB","OSB1","OSB2","OSB3","OSB4","UBOSB","0CE0"
"50G4","67G4","67G4T","*","MPP1","MABC1","MPP2","MABC2","0B74"
"50Q1","67Q1","67Q1T","50Q2","67Q2","67Q2T","59N1","59N2","0B90"
"50Q3","67Q3","67Q3T","50Q4","67Q4","67Q4T","59Q","59V1","0B75"
"51Q","51QT","51QR","*","*","Z2PGS","67QG2S","BTX","0A8D"
"Z3XT","DSTRT","NSTRT","STOP","Z3RB","KEY","EKEY","ECTT","0D93"
"PTRX","UBB1","UBB2","UBB","WFC","PT","PTRX1","PTRX2","0C3F"
"27A","27B","27C","59A","59B","59C","3P27","3P59","096E"
"27AB","27BC","27CA","59AB","59BC","59CA","*","*","0971"
"OUT201","OUT202","OUT203","OUT204","OUT205","OUT206","OUT207","OUT208","0FF4"
"OUT209","OUT210","OUT211","OUT212","MPP3","MABC3","MPP4","MABC4","0E85"
"IN208","IN207","IN206","IN205","IN204","IN203","IN202","IN201","0CEC"
"RMB8A","RMB7A","RMB6A","RMB5A","RMB4A","RMB3A","RMB2A","RMB1A","0E34"
"TMB8A","TMB7A","TMB6A","TMB5A","TMB4A","TMB3A","TMB2A","TMB1A","0E44"
"RMB8B","RMB7B","RMB6B","RMB5B","RMB4B","RMB3B","RMB2B","RMB1B","0E3C"
"TMB8B","TMB7B","TMB6B","TMB5B","TMB4B","TMB3B","TMB2B","TMB1B","0E4C"
"LBOKB","CBADB","RBADB","ROKB","LBOKA","CBADA","RBADA","ROKA","0DFA"
"81D1","81D2","81D3","81D4","81D5","81D6","27B81","*","0A01"
"81D1T","81D2T","81D3T","81D4T","81D5T","81D6T","*","*","0B0F"<ETX>
Messages for other relay models may be derived from the appropriate tables in
Section 9: Setting the Relay of this manual, using the above format.
BNA Message
In response to the BNA command, the relay sends names of the bits
transmitted in the Status Byte in the A5D1 message. The first name is the
MSB, the last name is the LSB. The BNA message is:
<STX>"*","*","*","STSET","*","*","*","*","yyyy"<ETX>
where:
<STX> = the STX character (02)
<ETX> = the ETX character (03)
the last field in each line is the 4-byte ASCII hex
representation of the checksum for the line
*
indicates an unused bit location
To Next Page
Loading...
