Schweitzer Engineering Laboratories SEL-311C - Page 15

xiiiList of Tables
Date Code 20060320 Instruction Manual SEL-311C Relay
Table 14.19 SEL-311C SELOGIC Control Equation Equivalent
to Each SEL-221F-3 Mask Logic Setting ......................................................................... 14.36
Table 14.20 SEL
OGIC Equivalent to SEL-221F-3 Relay Word Bits ...................................................... 14.36
Table 14.21 Default SEL-221F Mask Logic Setting for MRC .............................................................. 14.37
Table 14.22 SEL-221F-3 Setting PSVC for Settings S, P, and E........................................................... 14.38
Table 14.23 SEL-221F-3 Setting BFIN1 ............................................................................................... 14.38
Table 14.24 SEL-311C Settings Calculated From SEL-221C Settings................................................. 14.40
Table 14.25 SEL-311C SEL
OGIC Control Equation Equivalent
to Each SEL-221C Mask Logic Setting............................................................................ 14.43
Table 14.26 SEL
OGIC Equivalent to SEL-221C Relay Word Bits......................................................... 14.43
Table 14.27 Default SEL-221C Mask Logic Setting for MTU.............................................................. 14.44
Table 14.28 SEL-311C Settings Calculated From SEL-221-16 Settings .............................................. 14.48
Table 14.29 SEL-311C SEL
OGIC Control Equation Equivalent
to Each SEL-221-16 Mask Logic Setting ......................................................................... 14.50
Table 14.30 SEL
OGIC Equivalent to SEL-221-16 Relay Word Bits ...................................................... 14.51
Table 14.31 Default SEL-221-16 Mask Logic Setting for MRC ........................................................... 14.51
Table 14.32 SEL-311C Settings Calculated From SEL-2PG10 Settings............................................... 14.54
Table 14.33 SEL-311C SEL
OGIC Control Equation Equivalent
to Each SEL-2PG10 Mask Logic Setting ......................................................................... 14.56
Table 14.34 SEL
OGIC Equivalent to SEL-2PG10 Relay Word Bits....................................................... 14.56
Table 14.35 Default SEL-2PG10 Mask Logic Setting for MT .............................................................. 14.57
Table A.1 Firmware Revision History ................................................................................................... A.1
Table A.2 Settings Change History........................................................................................................ A.4
Table A.3 Instruction Manual Revision History .................................................................................... A.5
Table B.1 Troubleshooting New Firmware Upload..............................................................................B.13
Table D.1 Binary Message List.............................................................................................................. D.2
Table D.2 ASCII Configuration Message List....................................................................................... D.2
Table D.3 A5C0 Relay Definition Block ............................................................................................... D.3
Table D.4 A5C1 Fast Meter Configuration Block ................................................................................. D.3
Table D.5 A5D1 Fast Meter Data Block................................................................................................ D.5
Table D.6 A5C2/A5C3 Demand/Peak Demand Fast Meter Configuration Messages........................... D.5
Table D.7 A5D2/A5D3 Demand/Peak Demand Fast Meter Message ................................................... D.8
Table D.8 A5CE Fast Operate Configuration Block.............................................................................. D.9
Table D.9 A5E0 Fast Operate Remote Bit Control.............................................................................. D.10
Table D.10 A5E3 Fast Operate Breaker Control ................................................................................... D.11
Table D.11 A5CD Fast Operate Reset Definition Block ....................................................................... D.11
Table D.12 A5ED Fast Operate Reset Command.................................................................................. D.12
Table E.1 Compressed ASCII Commands .............................................................................................E.1
Table E.2 Mapping Bits to Labels ........................................................................................................E.10
Table G.1 SEL Fast Message Protocol Format ...................................................................................... G.5
Table G.2 Unsolicited Fast Message Enable Packet .............................................................................. G.6
Table G.3 Unsolicited Fast Message Disable Packet ............................................................................. G.6
Table G.4 Permissible Message Periods Requested by Enable Message .............................................. G.7
Table G.5 SEL-311C Global Settings for Synchrophasors.................................................................... G.8
Table G.6 SEL-311C Serial Port Settings for Synchrophasors.............................................................. G.8
Table G.7 Time Synchronization Relay Word Bits.............................................................................. G.11
Table G.8 SEL Fast Message Voltage and Current Selections Based on PHDATAV and PHDATAI.. G.14
Table H.1 SEL
OGIC Control Equation Operators (Listed in Processing Order) .................................... H.4
Table I.1 Data Needed to Configure a Port for DNP..............................................................................I.2
Table I.2 Data Access Methods..............................................................................................................I.5
Table I.3 SEL-311C DNP3 Device Profile.............................................................................................I.6
Table I.4 SEL-311C Relay DNP Object Table .......................................................................................I.7
Table I.5 SEL-311C-Wye DNP Data Map ...........................................................................................I.10
Table J.1 Error Types Reported by the Communications Report ...........................................................J.3
Table K.1 Message Format for Function Code 01 ................................................................................. K.4
Table K.2 Message Format for Function Code 02 ................................................................................. K.5
Table K.3 Message Format for Function Code 18 ................................................................................. K.5
Table K.4 Format of Message if SER Records Have Been Lost............................................................ K.6