Shading denotes a peripheral module not available for this configuration.
UTOPIA
McBSP0
TIMER0
EMIFA
GPIO
TIMER1
PLL1
and PLL1
Controller
DDR2
EMIF
VCP2
AED[63:0]
64
AECLKIN, AARDY, AHOLD
AEA[22:3], ACE[3:0], ABE[7:0],
AECLKOUT, ASDCKE,
AHOLDA, ABUSREQ,
ASADS
/ASRE, AAOE/ASOE,
AAWE
/ASWE
SCL
SDA
CLKIN1, PLLV1
SYSCLK4
RIOCLK, RIOCLK, RIOTX[3:0],
RIOTX[3:0]
, RIORX[3:0], RIORX[3:0]
HRDY, HINT
HCNTL0, HCNTL1, HHWIL,
HAS
, HR/W, HCS, HDS1, HDS2
CLKR0, FSR0, DR0, CLKS0,
DX0, FSX0, CLKX0
MRXD[7:0], MRXER, MRXDV, MCOL,
MCRS, MTCLK, MRCLK
32
HD[31:0]
TCP2
CLKIN2, PLLV2
GP[15:12,2,1]
DEA[21:2], DCE[1:0], DBE[3:0], DDRCLK, DDRCLK,
DSDCKE, DDQS, DDQS
, DSDCAS, DSDRAS,
DSDWE
AEA[19:16] (BOOTMODE[3:0]) = 0001, (HPI Boot)
AEA[15] (AECLKIN_SEL) = 0, (AECLKIN, default)
AEA[14] (HPI_WIDTH) = 1, (HPI, 32-bit Operation)
AEA[13] (LENDIAN) = IPU, (Little Endian Mode, default)
AEA[12] (UTOPIA_EN) = 0, (UTOPIA disabled, default)
AEA[10:9] (MACSEL[1:0]) = 00, (10/100 MII Mode)
AEA[8] (PCI_EEAI) = 0, (PCI I2C EEPROM Auto-Init disabled, default)
AEA[7] = 0, (do not oppose IPD)
AEA[6] (PCI66) = 0, (PCI 33 MHz [default, don’t care])
AEA[5] (MCBSP1_EN) = 1, (McBSP1 enabled)
AEA[4] (SYSCLKOUT_EN) = 1, (SYSCLK4 pin function)
AEA[2:0] (CFGGP[2:0]) = 000 (default)
McBSP1
EMAC
RapidIO
32
ED[31:0]
TINP1L
TOUT1L
TOUT0
TINP0
MTXD[7:0], MTXEN,
MDIO, MDCLK
MDIO
I2C
PCI
HPI
(32-Bit)
CLKR1, FSR1, DR1, CLKS1,
DX1, FSX1, CLKX1
DEVSTAT Register: 0x0061 C161
PCI_EN = 0 (PCI disabled, default)
ABA1 (EMIFA_EN) = 1(EMIFA enabled)
ABA0 (DDR2_EN) = 1 (DDR2 Memory Controller enabled)
PLL2
and PLL2
Controller
To Next Page
Loading...
Need help?
General
