ADCMT 6166 - Page 13

6166 DC Voltage Current Source Operation Manual
Table of Contents
C-3
4.2.8 EXTERNAL GUARD Key (GUARD Terminal Connection) ................... 4-3
4.2.9 EXTERNAL SENSE Key (Output Terminal Connection) ........................ 4-3
4.2.10 FNo./LNo. STEP TIME Key (First/Last Number and Step Time Setting) 4-4
4.2.11 LIMIT Key (Voltage and Current Limit Setting) ....................................... 4-4
4.2.12 MEMORY Key (Program Memory Setting) .............................................. 4-4
4.2.13 MENU Key (Parameter Setting) ................................................................ 4-4
4.2.14 OPERATE Key (Output ON/OFF) ............................................................ 4-8
4.2.15 POLARITY+ Key (Source Value Polarity and Zero) ................................ 4-8
4.2.16 POLARITY 0 Key (Source Value Polarity and Zero) ............................... 4-8
4.2.17 POLARITY- Key (Source Value Polarity and Zero) ................................. 4-8
4.2.18 PROGRAM Key (Switching to and Releasing Program Function) ........... 4-9
4.2.19 RECALL key (Memory Recall) ................................................................. 4-9
4.2.20 SAVE Key (Memory Setting Saving) ........................................................ 4-9
4.2.21 UP Key (Source Range UP) ....................................................................... 4-9
4.2.22 SCAN Key (Setting Memory Scan) ........................................................... 4-10
4.2.23 START/PAUSE Key (Starting and Pausing Memory Scan) ...................... 4-10
4.2.24 STOP Key (Stopping Memory Scan) ......................................................... 4-10
5. OPERATIONAL DESCRIPTIONS ........................................................ 5-1
5.1 Connection with Load ....................................................................................... 5-1
5.1.1 Configuration of Output Terminals ............................................................ 5-1
5.1.2 2-Wire and 4-Wire Connections ................................................................. 5-1
5.1.3 How to Use Guard Terminal ...................................................................... 5-4
5.1.4 Selecting Standby Status ............................................................................ 5-6
5.2 Source and Sink Operations .............................................................................. 5-7
5.3 HIGH VOLTAGE Indicator Operation and Output Status ............................... 5-8
5.3.1 HIGH VOLTAGE Indicator Operation ...................................................... 5-8
5.3.2 Output Status at HIGH VOLTAGE Indicator ON ..................................... 5-8
5.3.3 Short Circuit at High Voltage Output ......................................................... 5-8
5.4 Output Operation Timing .................................................................................. 5-9
5.4.1 Setting Data Change Timing ...................................................................... 5-9
5.4.2 Output ON (OPR)/OFF (STBY) Timing .................................................... 5-10
5.4.3 Range Change Timing ................................................................................ 5-10
5.4.4 Function Change Timing ............................................................................ 5-11
5.4.5 Polarity Change Timing ............................................................................. 5-12
5.5 Other Operations ............................................................................................... 5-13
5.5.1 Precautions for Setting Voltage Limit ........................................................ 5-13
5.5.2 Voltage Limit Error at Current Source ....................................................... 5-14
5.5.3 Voltage Output (1000 V and 100 V Ranges) and Current Limit Detection 5-15
5.5.4 TRIGGER IN Signal .................................................................................. 5-16
5.5.5 INTERLOCK Input Signal ......................................................................... 5-18
5.5.6 Self Test ...................................................................................................... 5-19
5.5.7 Error Log .................................................................................................... 5-21
5.6 Operational Principles ....................................................................................... 5-22
6. REMOTE PROGRAMMING ................................................................... 6-1
6.1 Using Interface .................................................................................................. 6-1
6.1.1 Selecting Interface ...................................................................................... 6-1