19R5910032 /00 Freya
On servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
• Refer all servicing to qualified service personnel.
• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
• Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via safetydatasheets@barco.com.
1.4 Product safety labels
Light beam related safety labels
Label image Label description
Label location
DANGER! CLASS 4 LASER RADIATION WHEN OPEN. AVOID EYE OR
SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION.
DANGER! RAYONNEMENT LASER DE CLASSE 4 EN CAS D’OUVERTURE.
EXPOSITION DANGEREUSE AU RAYONNEMENT DIRECT OU DIFFUS
DES YEUX OU DE LA PEAU.
危险! 打开时有4类激光辐射。 避免眼或皮肤受到直射或散射辐射的照射。
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2018-V-2875 EFFECTIVE ON OCTOBER 2, 2018
ATTENTION! NE PAS REGARDER LE FAISCEAU
EVITER TOUTE EXPOSITION DIRECTE DES YEUX AU FAISCEAU
RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN 60825-1:2014
DISTANCE DE SECURITE: CONSULTER LE MANUEL DE SECURITE
WARNING! DO NOT LOOK INTO THE BEAM
NO DIRECT EYE EXPOSURE TO THE BEAM IS PERMITTED
RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN 60825-1:2014
HAZARD DISTANCE: CONSULT SAFETY MANUAL
RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN 60825-1:2014RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN 60825-1:2014
WARNING! DO NOT LOOK INTO THE BEAM; NO DIRECT EYE EXPOSURE
TO THE BEAM IS PERMITTED. RG3 IEC EN 62471–5:2015. CLASS 1 IEC
EN 60825–1:2014. HAZARD DISTANCE: CONSULT SAFETY MANUAL.
“Important safety instructions”, page 16
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS
FOR LASER PRODUCTS UNDER 21 CFR 1040 EXCEPT WITH RESPECT
TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER
2018-V-2875 EFFECTIVE ON OCTOBER 02, 2018.
Safety
To Next Page
Loading...
Need help?
General
