EasyManuals Logo

Dell S4048T User Manual

Dell S4048T
1277 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #257 background imageLoading...
Page #257 background image
Example of Viewing Aggregated Routes
In the show ip bgp command, aggregates contain an ‘a’ in the first column (shown in bold) and routes
suppressed by the aggregate contain an ‘s’ in the first column.
Dell#show ip bgp
BGP table version is 0, local router ID is 10.101.15.13
Status codes: s suppressed, d damped, h history, * valid, > best
Path source: I - internal, a - aggregate, c - confed-external, r - redistributed,
n - network
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 7.0.0.0/29 10.114.8.33 0 0 18508 ?
*> 7.0.0.0/30 10.114.8.33 0 0 18508 ?
*>a 9.0.0.0/8 192.0.0.0 32768 18508 701 {7018 2686 3786} ?
*> 9.2.0.0/16 10.114.8.33 0 18508 701 i
*> 9.141.128.0/24 10.114.8.33 0 18508 701 7018 2686 ?
Dell#
Configuring BGP Confederations
Another way to organize routers within an AS and reduce the mesh for IBGP peers is to configure BGP
confederations.
As with route reflectors, BGP confederations are recommended only for IBGP peering involving many IBGP
peering sessions per router. Basically, when you configure BGP confederations, you break the AS into smaller
sub-AS, and to those outside your network, the confederations appear as one AS. Within the confederation
sub-AS, the IBGP neighbors are fully meshed and the MED, NEXT_HOP, and LOCAL_PREF attributes are
maintained between confederations.
To configure BGP confederations, use the following commands.
Specifies the confederation ID.
CONFIG-ROUTER-BGP mode
bgp confederation identifier as-number
as-number: from 0 to 65535 (2 Byte) or from 1 to 4294967295 (4 Byte).
Specifies which confederation sub-AS are peers.
CONFIG-ROUTER-BGP mode
bgp confederation peers as-number [... as-number]
as-number: from 0 to 65535 (2 Byte) or from 1 to 4294967295 (4 Byte).
All Confederation routers must be either 4 Byte or 2 Byte. You cannot have a mix of router ASN support.
To view the configuration, use the show config command in CONFIGURATION ROUTER BGP mode.
Enabling Route Flap Dampening
When EBGP routes become unavailable, they “flap” and the router issues both WITHDRAWN and UPDATE
notices.
A flap is when a route:
Border Gateway Protocol IPv4 (BGPv4) 257

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dell S4048T and is the answer not in the manual?

Dell S4048T Specifications

General IconGeneral
Switching Capacity1.44 Tbps
Rack Units1U
Form FactorRack-mountable
Power DeviceInternal power supply
Power RedundancyOptional
Product TypeSwitch
Jumbo Frame SupportYes
Routing ProtocolOSPF, BGP, RIP, VRRP, PIM-SM, IGMP
Remote Management ProtocolSNMP, RMON, Telnet, SSH
FeaturesQuality of Service (QoS), Jumbo Frames Support, Virtual Route Redundancy Protocol (VRRP), VLAN support, sFlow, Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree Protocol (RSTP), IPv6 support
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ae
Dimensions (W x D x H)17.3 in x 16 in x 1.7 in
Operating Temperature0°C to 40 °C
Operating Humidity10% to 90% (non-condensing)

Related product manuals