EasyManuals Logo

Dell S4048T User Manual

Dell S4048T
1277 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #797 background imageLoading...
Page #797 background image
Dell(conf-if-te-1/1)#show config
!
interface TenGigabitEthernet 1/1
ip address 10.11.1.254/24
ip access-group testflow in
shutdown
Dell(conf-if-te-1/1)#exit
Dell(conf)#do show ip accounting access-list testflow
!
Extended Ingress IP access list testflow on TenGigabitEthernet 1/1
Total cam count 4
seq 5 permit icmp any any monitor count bytes (0 packets 0 bytes)
seq 10 permit ip 102.1.1.0/24 any monitor count bytes (0 packets 0 bytes)
seq 15 deny udp any any count bytes (0 packets 0 bytes)
seq 20 deny tcp any any count bytes (0 packets 0 bytes)
Dell(conf)#do show monitor session 0
SessionID Source Destination Direction Mode Type
--------- ------ ----------- --------- ---- ----
0 Te 1/1 Te 1/2 rx interface Flow-based
Remote Port Mirroring
While local port monitoring allows you to monitor traffic from one or more source ports by directing it to a
destination port on the same switch/router, remote port mirroring allows you to monitor Layer 2 and Layer 3
ingress and/or egress traffic on multiple source ports on different switches and forward the mirrored traffic to
multiple destination ports on different switches.
Remote port mirroring helps network administrators monitor and analyze traffic to troubleshoot network
problems in a time-saving and efficient way.
In a remote-port mirroring session, monitored traffic is tagged with a VLAN ID and switched on a user-
defined, non-routable L2 VLAN. The VLAN is reserved in the network to carry only mirrored traffic, which is
forwarded on all egress ports of the VLAN. Each intermediate switch that participates in the transport of
mirrored traffic must be configured with the reserved L2 VLAN. Remote port monitoring supports mirroring
sessions in which multiple source and destination ports are distributed across multiple switches
Remote Port Mirroring Example
Remote port mirroring uses the analyzers shown in the aggregation network in Site A.
The VLAN traffic on monitored links from the access network is tagged and assigned to a dedicated L2 VLAN.
Monitored links are configured in two source sessions shown with orange and green circles. Each source
session uses a separate reserved VLAN to transmit mirrored packets (mirrored source-session traffic is shown
with an orange or green circle with a blue border).
Port Monitoring 797

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Dell S4048T and is the answer not in the manual?

Dell S4048T Specifications

General IconGeneral
Switching Capacity1.44 Tbps
Rack Units1U
Form FactorRack-mountable
Power DeviceInternal power supply
Power RedundancyOptional
Product TypeSwitch
Jumbo Frame SupportYes
Routing ProtocolOSPF, BGP, RIP, VRRP, PIM-SM, IGMP
Remote Management ProtocolSNMP, RMON, Telnet, SSH
FeaturesQuality of Service (QoS), Jumbo Frames Support, Virtual Route Redundancy Protocol (VRRP), VLAN support, sFlow, Multiple Spanning Tree Protocol (MSTP), Rapid Spanning Tree Protocol (RSTP), IPv6 support
Compliant StandardsIEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3ae
Dimensions (W x D x H)17.3 in x 16 in x 1.7 in
Operating Temperature0°C to 40 °C
Operating Humidity10% to 90% (non-condensing)

Related product manuals