Hioki 3153 - Command Table

164
_____________________________________________________________________________________________
10.2 Command Table
______________________________________________________________________________________________
Command Explanation Page
∗CLS
Clears the status byte register and the event registers. 168
∗ESR?
Queries the contents of the standard event status register. 168
∗IDN?
Queries manufacturer's name, model name, and software version. 169
∗RST
Performs device initial setting. 169
∗TST?
Requests execution of, and queries the result of, the self test. 170
Command Explanation Page
:ESR0?
Queries event status register 0. 171
:HEADer Enables and disables headers for the response messages. 171
:HEADer?
Queries whether or not headers on response messages are
enabled.
172
:SYSTem:ERRor?
Queries RS-232C communication errors. 172
:MODE Sets the test mode. 173
:MODE?
Queries the test mode. 173
:STATe? Queries the state. 174
:STARt
Starting a test. 174
:STOP Forcibly ends a test and releases the hold state. 175
:CONFigure:WITHstand:KIND
Sets the type of test voltage. 175
:CONFigure:WITHstand:KIND? Queries the type of voltage for withstand-voltage tests. 175
:CONFigure:WITHstand:VOLTage
Sets the test-voltage value for withstand-voltage tests. 176
:CONFigure:WITHstand:VOLTage? Queries the test-voltage value for withstand-voltage tests. 176
:CONFigure:WITHstand:CUPPer
Sets the upper-limit value for withstand-voltage tests. 176
:CONFigure:WITHstand:CUPPer? Queries the upper-limit value for withstand-voltage tests. 177
:CONFigure:WITHstand:CLOWer
Sets the lower-limit value for withstand-voltage tests. 177
:CONFigure:WITHstand:CLOWer? Queries the lower-limit value for withstand-voltage tests. 177
:CONFigure:WITHstand:TIMer
Sets the test time for withstand-voltage tests. 178
:CONFigure:WITHstand:TIMer? Queries the test time for withstand-voltage tests. 178
:CONFigure:WITHstand:UTIMer
Sets the ramp-up time for withstand-voltage tests. 178
:CONFigure:WITHstand:UTIMer? Queries the ramp-up time for withstand-voltage tests. 179
:CONFigure:WITHstand:DTIMer
Sets the ramp-down time for withstand-voltage tests. 179
:CONFigure:WITHstand:DTIMer? Queries the ramp-down time for withstand-voltage tests. 179
:WITHstand:CLOWer
Enables and disables the lower-limit value for withstand-
voltage tests.
180
:WITHstand:CLOWer?
Queries the lower-limit value enablement for withstand-
voltage tests.
180
:WITHstand:TIMer
Enables and disables the test time for withstand-voltage tests. 180
:WITHstand:TIMer? Queries the test time enablement for withstand-voltage tests. 181
:WITHstand:UTIMer
Sets the ramp-up time ON/OFF for withstand-voltage tests. 181
:WITHstand:UTIMer? Queries the ramp-up time ON/OFF for withstand-voltage tests. 181
:WITHstand:DTIMer
Sets the ramp-down time ON/OFF for withstand-voltage tests. 182
10.2 Command Table
Common Commands (RS-232C/ GP-IB)
Specific Commands (RS-232C/ GP-IB)