[S9300-C-Vlanif400] pim sm
[S9300-C-Vlanif400] quit
# Configure the service boundary of BSR on VLANIF 500 of S9300-A, VLANIF 200 of S9300-
B, VLANIF 200 of S9300-E, and VLANIF 500 of S9300-F. The configurations of S9300-B,
S9300-E, and S9300-F are similar to configuration of S9300-A, and are not mentioned here.
[S9300-A] interface vlanif 500
[S9300-A-Vlanif500] pim bsr-boundary
[S9300-A-Vlanif500] quit
Step 3 Configure Loopback0, C-BSR, and C-RP.
# Configure loopback0, C-BSR, and C-RP on S9300-C, S9300-D, and S9300-F. The
configurations of S9300-D and S9300-F are similar to the configuration of S9300-C, and are
not mentioned here.
[S9300-C] interface loopback 0
[S9300-C-LoopBack0] ip address 1.1.1.1 255.255.255.255
[S9300-C-LoopBack0] pim sm
[S9300-C-LoopBack0] quit
[S9300-C] pim
[S9300-C-pim] c-bsr loopback 0
[S9300-C-pim] c-rp loopback 0
[S9300-C-pim] quit
Step 4 Configure static RPF peers.
# Configure S9300-D and S9300-F as the static RPF peers of S9300-C.
[S9300-C] ip ip-prefix list-df permit 192.168.0.0 16 greater-equal 16 less-equal
32
[S9300-C] msdp
[S9300-C-msdp] peer 192.168.3.2 connect-interface vlanif100
[S9300-C-msdp] peer 192.168.5.1 connect-interface vlanif400
[S9300-C-msdp] static-rpf-peer 192.168.3.2 rp-policy list-df
[S9300-C-msdp] static-rpf-peer 192.168.5.1 rp-policy list-df
[S9300-C-msdp] quit
# Configure S9300-C as the static RPF peer of S9300-D and S9300-F. The configuration of
S9300-F is similar to the configuration of S9300-D, and is not mentioned here.
[S9300-D] ip ip-prefix list-c permit 192.168.0.0 16 greater-equal 16 less-equal 32
[S9300-D] msdp
[S9300-D-msdp] peer 192.168.1.1 connect-interface vlanif300
[S9300-D-msdp] static-rpf-peer 192.168.1.1 rp-policy list-c
Step 5 Verify the configuration.
# Run the display bgp peer command to view the status of the BGP peer relation between
S9300s. No output information is displayed on S9300-C, which indicates that no BGP peer
relation is set up between S9300-C and S9300-D, and between S9300-C and S9300-F.
# Run the display msdp brief command to view the status of the MSDP peer relation between
S9300s. When multicast source S1 in the PIM-SM1 domain sends multicast packets, the
receivers in the PIM-SM2 and PIM-SM3 domains can receive the packets. For example, the
displayed information of MSDP peers on S9300-C, S9300-D and S9300-F is as follows:
<S9300-C> display msdp brief
MSDP Peer Brief Information of VPN-Instance: public net
Configured Up Listen Connect Shutdown Down
2 2 0 0 0 0
Peer's Address State Up/Down time AS SA Count Reset Count
192.168.3.2 UP 01:07:08 ? 8 0
192.168.5.1 UP 00:16:39 ? 13 0
Quidway S9300 Terabit Routing Switch
Configuration Guide - Multicast 5 MSDP Configuration
Issue 01 (2009-07-28) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5-37
To Next Page
Loading...
