Schweitzer Engineering SEL-2032 - Page 201

13
Date Code 20120126 Instruction Manual SEL-2032 Communications Processor
Settings Sheets
SEL-2701, SET P, and SET A
Date: ________________________________
Approved by: _________________________
SEL-2032 S/N: _______________________
CTRLB39 Control bit 39 assignment (msg=1–8:bit=0–160) ____________________
CTRLB40 Control bit 40 assignment (msg=1–8:bit=0–160) ____________________
CTRLB41 Control bit 41 assignment (msg=1–8:bit=0–160) ____________________
CTRLB42 Control bit 42 assignment (msg=1–8:bit=0–160) ____________________
CTRLB43 Control bit 43 assignment (msg=1–8:bit=0–160) ____________________
CTRLB44 Control bit 44 assignment (msg=1–8:bit=0–160) ____________________
CTRLB45 Control bit 45 assignment (msg=1–8:bit=0–160) ____________________
CTRLB46 Control bit 46 assignment (msg=1–8:bit=0–160) ____________________
CTRLB47 Control bit 47 assignment (msg=1–8:bit=0–160) ____________________
CTRLB48 Control bit 48 assignment (msg=1–8:bit=0–160) ____________________
CTRLB49 Control bit 49 assignment (msg=1–8:bit=0–160) ____________________
CTRLB50 Control bit 50 assignment (msg=1–8:bit=0–160) ____________________
CTRLB51 Control bit 51 assignment (msg=1–8:bit=0–160) ____________________
CTRLB52 Control bit 52 assignment (msg=1–8:bit=0–160) ____________________
CTRLB53 Control bit 53 assignment (msg=1–8:bit=0–160) ____________________
CTRLB54 Control bit 54 assignment (msg=1–8:bit=0–160) ____________________
CTRLB55 Control bit 55 assignment (msg=1–8:bit=0–160) ____________________
CTRLB56 Control bit 56 assignment (msg=1–8:bit=0–160) ____________________
CTRLB57 Control bit 57 assignment (msg=1–8:bit=0–160) ____________________
CTRLB58 Control bit 58 assignment (msg=1–8:bit=0–160) ____________________
CTRLB59 Control bit 59 assignment (msg=1–8:bit=0–160) ____________________
CTRLB60 Control bit 60 assignment (msg=1–8:bit=0–160) ____________________
CTRLB61 Control bit 61 assignment (msg=1–8:bit=0–160) ____________________
CTRLB62 Control bit 62 assignment (msg=1–8:bit=0–160) ____________________
CTRLB63 Control bit 63 assignment (msg=1–8:bit=0–160) ____________________
CTRLB64 Control bit 64 assignment (msg=1–8:bit=0–160) ____________________
ENDNP Enable DNP3 (Y,N) ____________________
DNPADR DNP3 Address (0–65519) ____________________
DNPPNUM DNP3 Port Number for TCP and UDP (1–65534) ____________________
DNPMAP DNP3 map Mode (AUTO, CUSTOM) ____________________
RPADR01 DNP3 Address for Master 1 (0–65519) ____________________
DNPIP01 IP Address for Master 1 (www.xxx.yyy.zzz) ____________________
DNPTR01 Transport Protocol for Master 1 (UDP, TCP) ____________________
DNPUP01 UDP Response Port Number for Master 1 (1–65534, REQ) ____________________
UNSL01 Enable Unsolicited Reporting for Master 1 (Y,N) ____________________
PUNSL01 Enable Unsolicited Reporting at Power up for Master 1 (Y,N) ____________________
DNPMP01 CUSTOM Mode: DNP3 map associated with Master 1 (1–5) ____________________
DNPCL01 Enable Controls for Master 1 (Y,N) ____________________
RPADR02 DNP3 Address for Master 2 (0–65519) ____________________
DNPIP02 IP Address for Master 2 (www.xxx.yyy.zzz) ____________________
DNPTR02 Transport Protocol for Master 2 (UDP, TCP) ____________________
Port ( 17 / 18 )
Courtesy of NationalSwitchgear.com