Codes for Activating/Deactivating Features Nur für den internen Gebrauch
A31003-H3590-S100-7-7620, 06/2012
B-14 HiPath 3000/5000 V9, Service documentation
fcodes.fm
Station num-
ber, assign for
MUSAP
*41+DID no. 7541... *41... – V – H – AN, DIG, ENT,
S0, CMI, IPSC
X – This must be fol-
lowed by seizure of
external line.
Ring transfer
on
*502+MULAP 75502 *502 – V, T – H – AN, DIG, ENT,
S0, CMI, IPSC
X Only for member of
the executive MU-
LAP groups
Ring transfer
off
#502+MULAP 76502 #502 – V, T – H – AN, DIG, ENT,
S0, CMI, IPSC
X Only for member of
the executive MU-
LAP groups
Ringing group
on
*81+Stn. no. 7581... *81... – U, V,
T
– H – AN, DIG, ENT,
S0, CMI, IPSC
X RK,
BS
Ringing group
off - all mem-
bers removed
#81 7681 #81 – U, V,
T
RH H – AN, DIG, ENT,
S0, CMI, IPSC
X RK,
BS
Ringer cutoff
on
– – *98 – V, T RH U1 Local
feature
DIG, IPSC X RK,
BS
A short advisory
tone is activated.
The optical signals
are retained.
Ringer cutoff
off
– – #98 – V, T RH U1 Local
feature
DIG, IPSC X RK,
BS
Hunt group,
join
*85 7585 *85 – V, T RH U1 Fea-
ture
menu
AN, DIG, ENT,
S0, CMI, IPSC
X RK,
BS
All hunt groups, join
= *85*
Hunt group,
leave
#85 7685 #85 – V, T RH U1 Fea-
ture
menu
AN, DIG, ENT,
S0, CMI, IPSC
X RK,
BS
All hunt groups,
leave = #85#
Service menu – – – X,
T
– – – – DIG, IPSC – BS Service key as for
stopping and start-
ing procedure
Remote ser-
vice call
*994+In-
dex+Suffix dial-
ing
75944 *994 – – – U1 – AN, DIG, ENT,
S0, CMI, IPSC
– –
Table B-1 Codes for Activating/Deactivating Features
Feature
Operating procedure for
Supported
workpoint cli-
ents
(see abbrevi-
ations in
Table B-2)
Locking of
feature
Note
TDM work-
point clients
without dis-
play,
CMI mobile
phones,
analog work-
point clients
1
S
0
work-
point cli-
ents
TDM workpoint clients with
display,
CMI feature mobile phones,
IP workpoint clients
OpenScape
Personal Edition
Code +
Procedure
Code
Code
Key Menu
Code
via
Telephone lock
Status
locking on
Fixed
Programm-
able
Dialog
Service
Abbreviations:
● Call states: RH = idle, BR = ready, WA = digit input, BS = busy, RK = incoming call, RG = outgoing call, GS = call
● Key programming: V = key can be programmed with complete feature, U = key can be programmed to start procedure, T = key with
toggle functionality
● Menu level: H = Main menu, U1 = 1st submenu, U2 = 2nd submenu
To Next Page
Loading...
