Siemens SIMATIC ET 200S - Page 24

Contents
xxii
ET 200S Distributed I/O System
EWA-4NEB 780602402-12
11-9 Terminal assignment of the 4DI 24 VUC High Feature 11-29............
11-10 Terminal assignment of NAMUR sensors or sensors as per DIN 19234 11-33
11-11 Terminal assignment of NAMUR changeover contacts or sensors as
per DIN 19234 11-34...............................................
11-12 Terminal assignment of single contact with 10 kΩ
(mechanical NO contact) 11-34......................................
11-13 Terminal assignment of changeover contact with 10 kΩ
(mechanical changeover contact) 11-35...............................
11-14 Terminal Assignment of a Single Contact without Load Resistance
(Mechanical NO Contact with Single Contact) 11-35....................
11-15 Terminal Assignment of a Changeover Contact without Load Resistance
(Mechanical Changeover Contact) 11-36..............................
11-16 Changeover Contact Diagnostics 11-40...............................
11-17 Terminal assignment of the 2DI 24 VDC Standard 11-41................
11-18 Terminal assignment of the 2DI 230 VAC Standard 11-45...............
11-19 Terminal assignment of the 2DO 24 VDC/0.5 A Standard 11-48..........
11-20 Terminal assignment of the 4DO 24 VDC/0.5 A Standard 11-52..........
11-21 Terminal assignment of the 2DO 24 VDC/0.5 A High Feature 11-56......
11-22 Terminal assignment of the 2DO 24 VDC/2 A Standard 11-60...........
11-23 Terminal assignment of the 4DO 24 VDC/2 A Standard 11-64...........
11-24 Terminal assignment of the 2DO 24 VDC/2 A High Feature 11-68........
11-25 Terminal assignment of the 2DO 24--230 VAC 11-72....................
11-26 Terminal assignment of the 2RO NO 24--120 VDC/5 A 24--230 VAC/5 A
(from product level 2) 11-77.........................................
11-27 Switching capacity and service life of relay contacts 11-80..............
11-28 Terminal assignment of the
2RO NO/NC 24--48 VDC/5 A 24--230 VAC/5 A 11-82...................
11-29 Switching capacity and service life of contacts 11-85...................
12-1 Measured Values in the Event of Wire Break Dependent on Enabled
Diagnostics 12-3..................................................
12-2 Analog Value Representation (SIMATIC S7 Format) 12-4...............
12-3 Measured Value Resolution of the Analog Values
(SIMATIC S7 Format) 12-4.........................................
12-4 SIMATIC S7 Format: Measuring ranges
 80 mV,  2.5 V,  5 V and  10 V 12-5.............................
12-5 SIMATIC S7 Format: Measuring ranges 1 to 5 V, 0 to 20 mA, 4
to 20 mA 12-6....................................................
12-6 SIMATIC S7 Format: Measuring range
 20 mA 12-6..................
12-7 SIMATIC S7 Format: Measuring ranges
150 Ω, 300 Ω, 600 Ω, 3000 Ω 12-7..................................
12-8 SIMATIC S7 Format: Measuring Ranges
Pt 100, 200, 500, 1000 Standard in
° C and ° F 12-8....................
12-9 SIMATIC S7 Format: Measuring Ranges
Pt 100, 200, 500, 1000 Climatic in
° C and ° F 12-8.....................
12-10 SIMATIC S7 Format: Measuring Ranges
Ni 100, 200, 500, 1000 Standard in
° C and ° F 12-9....................
12-11 SIMATIC S7 Format: Measuring Ranges
Ni 100, 120, 200, 500, 1000 Climatic in
° C and ° F 12-9.................
12-12 SIMATIC S7 Format: Measuring Ranges
Cu 10 Standard in
° C and ° F 12-10...................................
12-13 SIMATIC S7 Format: Measuring Ranges
Cu 10 Climatic in
° C and ° F 12-10....................................
12-14 SIMATIC S7 Format: Measuring Range Type B in
° C and ° F 12-11.......
12-15 SIMATIC S7 Format: Measuring Range Type C in
° C and ° F 12-11.......
12-16 SIMATIC S7 Format: Measuring Range Type E in
° C and ° F 12-12.......