Suzuki SFV650 - Tightening Torque Specifications

Engine Mechanical: 1D-86
Tightening Torque Specifications
B944H11407002
Fastening part
Tightening torque
Note
N⋅m kgf-m lbf-ft
STP sensor mounting screw 3.5 0.35 2.5 )(Page 1D-13)
TP sensor mounting screw 3.5 0.35 2.5 )(Page 1D-14)
Fuel delivery pipe mounting screw 5 0.5 3.5 )(Page 1D-15)
Clutch release arm bolt 9 0.9 6.5 )(Page 1D-24)
Engine sprocket nut 145 14.5 105.0 )(Page 1D-24)
Speed sensor rotor bolt 25 2.5 18.0 )(Page 1D-24)
Speed sensor mounting bolt 5 0.5 3.5 )(Page 1D-24)
Cylinder head bolt (M10) (Initial) 25 2.5 18.0 )(Page 1D-33)
Cylinder head bolt (M10) (Final) 42 4.2 30.5 )(Page 1D-33)
Cylinder head bolt (M6) (L70) 10 1.0 7.0 )(Page 1D-33)
Cylinder head bolt (M6) (L40) 10 1.0 7.0 )(Page 1D-33)
Cylinder nut (M6) 10 1.0 7.0 )(Page 1D-34)
Camshaft journal holder bolt
10 1.0 7.0
)(Page 1D-36) /
)(Page 1D-39) /
)(Page 1D-44)
Cam chain tension adjuster bolt
10 1.0 7.0
)(Page 1D-36) /
)(Page 1D-40)
Cam chain tension adjuster cap bolt
23 2.3 16.5
)(Page 1D-36) /
)(Page 1D-40)
Generator cover plug 11 1.1 8.0 )(Page 1D-41)
Valve timing inspection plug 23 2.3 16.5 )(Page 1D-41)
Cylinder head cover bolt 14 1.4 10.0 )(Page 1D-42)
Exhaust pipe bolt 23 2.3 16.5 )(Page 1D-42)
Oil gallery plug (Cylinder head) (M6) 10 1.0 7.0 )(Page 1D-49)
Oil gallery plug (M6)
10 1.0 7.0
)(Page 1D-66) /
)(Page 1D-68)
Oil gallery plug (M8)
18 1.8 13.0
)(Page 1D-66) /
)(Page 1D-68)
Oil gallery plug (M12) 21 2.1 15.0 )(Page 1D-66)
Oil gallery plug (M16) 35 3.5 25.5 )(Page 1D-66)
Special tool bolt 23 2.3 16.5 )(Page 1D-67)
Piston cooling oil jet bolt 10 1.0 7.0 )(Page 1D-69)
Oil pressure regulator 27 2.7 19.5 )(Page 1D-70)
Crankcase bolt (M8) 26 2.6 19.0 )(Page 1D-71)
Crankcase bolt (M6) 11 1.1 8.0 )(Page 1D-71)
Oil plate bolt 10 1.0 7.0 )(Page 1D-72)
Cam chain tensioner bolt
10 1.0 7.0
)(Page 1D-73) /
)(Page 1D-74)
Primary drive gear bolt 70 7.0 50.5 )(Page 1D-74)
Oil pressure switch 14 1.4 10.0 )(Page 1D-74)
Oil cooler union bolt 70 7.0 50.5 )(Page 1D-75)
Gearshift cam stopper bolt 10 1.0 7.0 )(Page 1D-75)
Gearshift cam stopper plate bolt 13 1.3 9.5 )(Page 1D-76)
Gearshift arm stopper 19 1.9 13.5 )(Page 1D-76)
Oil pipe stopper screw 8 0.8 6.0 )(Page 1D-77)
Generator cover mounting bolt 10 1.0 7.0 )(Page 1D-78)
Starter motor mounting bolt 10 1.0 7.0 )(Page 1D-78)
Conrod cap bolt 21 N⋅m (2.1 kgf-m, 15.0 lbf-ft) then turn in 1/
4 (90°) turn
)(Page 1D-80) /
)(Page 1D-81)