YOKOGAWA CENTUM CS 3000 - Page 210

Ind-2
TI 33Q01J10-01E Sep. 30, 2008-00
Concrete Floor .................................................... 2-11
Condensation ........................................................1-
5
Conduit Power-cabling ........................................3-1
0
Connecting Bus Cable ........................................3-8
8
Connecting Ground Cable .................................. 3-1
1
Connecting Optical Fiber Cable ........................3-10
5
Connecting Power ................................................3-
5
Connecting Relay Board with Digital
I/O Module ...................................................3-5
8
Connecting Signal Cable ....................................3-3
0
Connecting Signal Cables to Terminals
(for FIO) .......................................................3-3
3
Connecting Signal Cables to Terminals
(for RIO) .......................................................3-3
9
Connecting Signal Cables with Analog
I/O Module ...................................................3-5
4
Connecting Signal Cables with Analog
I/O Modules .................................................3-6
6
Connecting Signal Cables with Communication
Modules .......................................................3-7
8
Connecting Signal Cables with Digital I/O Modules
(Connector Type) .........................................3-7
7
Connecting Signal Cables with Digital I/O Modules
(Terminal Type) ............................................3-7
6
Connecting Signal Cables with Fieldnetwork I/O
(FIO) ............................................................3-4
9
Connecting Signal Cables with FIO ....................3-5
3
Connecting Signal Cables with MCM Terminal
Board ...........................................................3-7
2
Connecting Signal Cables with Multiplexer Modules
(Connector Type) .........................................3-7
5
Connecting Signal Cables with Multiplexer Modules
(Terminal Type) ............................................3-7
4
Connecting Signal Cables with Multipoint Control
Analog I/O Module AMC80 ..........................3-7
1
Connecting Signal Cables with PROFIBUS
Communication Module ACP71 ..................3-8
7
Connecting Signal Cables with Pulse Input
Module AAP135 ...........................................3-5
5
Connecting Signal Cables with Pulse Input Module
APM11 .........................................................3-6
8
Connecting Signal Cables with Relay I/O
Modules .......................................................3-7
3
Connecting Signal Cables with Remote I/O
(RIO) ............................................................3-6
4
Connecting Terminal Board with FIO ..................3-5
7
Connecting the Fieldbus Cable and Handling the
Shield Mesh for Fieldbus Communication
Module ACF11 .............................................3-8
5
Connecting to Pressure-clamp Terminal .............3-3
3
Connecting V net cables (10BASE-2) ................3-8
9
Connecting V net cables (10BASE-5) ................3-9
2
Connecting V net cables (10BASE-5) and
V net cables (10BASE-2) Interconnection
Example .......................................................3-9
0
Connection of Fieldbus Communication Module
ALF111 .........................................................3-6
0
Connector Type IOU Cabling ..............................3-4
5
Connector Type Multiplexer Module and Terminal
Board/Terminal Block ..................................3-7
5
Control Bus Adapter ............................................3-9
1
Control Room Design ...........................................1-
2
Control Room Environment ..................................1-
5
Corrosive-gas Environment Compatibility ..........1-3
3
Countermeasures against Static Electricity ........1-3
0
Crest factor ..........................................................1-1
6
D
Desktop Equipment ............................................2-29
Desk (YAX101, YAX801) ....................................2-3
0
Digital I/O Modules ADM11C, ADM12C,
ADM51C, ADM52C .....................................3-7
7
Distance between Cables ...................................1-3
1
Don’t Stack Outdoors ............................................2-
2
Dual-redundant Pressure Clamp Terminal .........3-5
3
E
Electric field strength (Electric wave condition) ....1-7
Electrical Specifications ........................................4-
1
EMC Conformity Standards ..................................1-
9
Enclosed Display Style Console Assembly
(LPCKIT) ......................................................3-1
2
Enclosed Display Style Console Type HIS
(LPCKIT) ......................................................1-2
0
ER Bus ................................................................3-9
9
ESB Bus ..............................................................3-9
7
Ethernet Communication Module ACM71
(For PFC
) ..................................................3-84
Examples of Arrester ...........................................1-2
9
Examples of Spark-killer Installation ...................1-2
9
Example of Implementation of Fieldbus
Communication Module ALF111 .................3-5
9
F
Fieldbus Wiring for ALF111 with Pressure
Clamp Terminal Block ..................................3-6
1
Fieldbus Wiring for ALF111 with Terminal
Board ...........................................................3-6
2
Field Cable Areas ................................................3-4
0
FIO Node Unit Wiring in FCU with Cabinet .........3-3
5
FIO Node Unit Wiring in I/O Expansion
Cabinet ........................................................3-3
6
FIO Signal Cabling ..............................................3-3
8