YOKOGAWA CENTUM CS 3000 - Page 212

Ind-4
TI 33Q01J10-01E Sep. 30, 2008-00
P
Paint Colors .........................................................4-19
Parts Durability ....................................................4-1
2
Passage ................................................................2-
4
PFCS/PFCD Field Control Station .............3-1
8, 4-17
Post-installation Environment Preservation ..........5-
1
Post-installation Inspection ...................................5-
1
Post-installation Inspection and Environmental
Preservation ..................................................5-
1
Power and Ground Cabling ................................3-1
2
Power Cables ........................................................3-
2
Power Cable Termination ......................................3-
7
Power Distribution Boards ....................................3-
8
Power Supply System .........................................1-1
4
Power Wiring When Connecting Dual Power
Supply Lines ................................................3-2
0
Precautions for Transportation ..............................2-
2
Pressure Clamp Terminal ..........................3-3
0, 3-53
Pressure Clamp Terminal (for ARS
M) ..........3-32
Pressure Clamp Terminal (for Pressure Clamp
Terminal Block) ............................................3-3
2
Process I/O Signal Connection ...........................3-3
0
Providing Area for Servicing ................................2-2
8
Providing Ground Bus in Cabinet/Console
Type HIS ......................................................1-2
3
Providing Space for Heat Radiation ....................2-2
7
R
Redundant AAM50/AAM51 ................................3-70
Relay Input Module ADM15R .............................3-7
3
Relay Output Module ADM55R ..........................3-7
3
RIO Bus .............................................................3-10
2
RIO Bus (19-inch Rack Mountable Type) .........3-10
2
RIO Bus (with Cabinet) .....................................3-10
3
RIO Bus Arrangement .......................................3-10
4
RIO bus Cabling ..................................................3-4
5
RIO Node Wiring in FCU Cabinet .......................3-4
1
RIO Node Wiring in I/O Expansion Cabinet ........3-4
2
Routing Signal Cables ...............................3-3
4, 3-41
RS-232C Communication Card ACM21 .............3-8
2
RS-232C Communication Module ACM11 .........3-7
8
RS-422/RS-485 Communication
Card ACM22 ................................................3-8
3
RS-422/RS-485 Communication Module
ACM12 .........................................................3-8
1
RTD Input Modules AMM32T, AMM32TJ ...........3-7
4
Rules of Connection for the Housekeeping Unit
(HKU) ...........................................................4-2
0
S
Safety Standards ..................................................1-8
Selecting a Power System ..................................1-1
6
Separate Grounding ...........................................1-2
2
Separator ............................................................1-3
1
Servicing Area .......................................................2-
9
Side-by-Side Cabinet Installation .........................1-
4
Signal Cables ........................................................3-
2
Signal Cables for Connection with RIO ..............3-6
5
Signal Cable Termination ....................................3-3
1
Size of Cabling Holes in Floor .............................2-1
4
Sleeve for pressure clamp terminal ......................3-
4
Solderless (crimp-on) Lug Specifications .............3-
7
Solderless Lug ................................... 3-
3, 3-30, 3-31
Source Output Capacity ......................................1-1
6
Standards for Hazardous Location Equipment ....1-
9
Status Contact Output Connection ...................3-10
7
Steel Floor ........................................................... 2-1
1
Storage ..................................................................2-
8
Storage Condition .................................................2-
8
Storage Environment ............................................2-
8
Storage of Packed Equipment ..............................2-
8
Storage of Unpacked Equipment ..........................2-
8
Structure of Clamp Filter and Mounting ..............3-8
0
Suppressing Harmonic Current ..........................1-1
7
System Installation Requirements ........................1-
1
T
Telephone .............................................................1-4
Temperatures and Humidity ..................................1-
5
Terminal Connection .............................................3-
9
Three-pin Plug Connection ...................................3-
9
Tools and Parts Required for Joining
Cabinets ......................................................2-2
2
Tools and Parts Required for Joining Console
Type HIS side by side ..................................2-1
9
To Use GI 62.5/125 Optical Fiber Cable ...........3-10
6
Transportation .......................................................2-
2
Transportation, Storage and Installation ...............2-
1
Transportation for LPCKIT, YPCKIT .....................2-
2
Type and Maximum Length of Power Cables .......3-
5