Fujitsu PRIMERGY RX100 S8 Upgrade And Maintenance Manual

Upgrade and Maintenance Manual RX100 S8
Contents
6.3.3.2 Removing the defective hot-plug power supply unit . . . . . 102
6.3.3.3 Installing the new hot-plug power supply unit . . . . . . . . 103
6.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 103
6.3.4 Replacing the power distribution board . . . . . . . . . . . . . 103
6.3.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 103
6.3.4.2 Removing the defective power distribution board . . . . . . 104
6.3.4.3 Installing the new power distribution board . . . . . . . . . 105
6.3.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 106
6.4 Converting a standard power supply to a redundant power
supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 107
6.4.2 Removing the standard power supply unit . . . . . . . . . . . 107
6.4.3 Installing the upgrade kit . . . . . . . . . . . . . . . . . . . . 108
6.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 112
7 Hard disk drives / solid state drives . . . . . . . . . . . . . 113
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 114
7.2 2.5-inch HDD/SSD configurations . . . . . . . . . . . . . . 115
7.2.1 Equipping the 2.5-inch HDD/SSD bays . . . . . . . . . . . . . 115
7.2.2 Configuration with up to four HDD/SSD modules . . . . . . . . 115
7.2.3 Configuration with up to eight HDD/SSD modules . . . . . . . 116
7.2.4 Configuration with up to 10 HDD/SSD modules . . . . . . . . 117
7.2.5 Installing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . 118
7.2.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 118
7.2.5.2 Removing a 2.5-inch HDD/SSD dummy module . . . . . . 118
7.2.5.3 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . 119
7.2.5.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 120
7.2.6 Removing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . 120
7.2.6.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 120
7.2.6.2 Removing a 2.5-inch HDD/SSD module . . . . . . . . . . 121
7.2.6.3 Installing a 2.5-inch HDD/SSD dummy module . . . . . . . 122
7.2.6.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 122
7.2.7 Replacing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 122
7.2.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 123
7.2.7.2 Removing the defective 2.5-inch HDD/SSD module . . . . 123
7.2.7.3 Installing the new 2.5-inch HDD/SSD module . . . . . . . . 123
7.2.7.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 123
7.2.8 Replacing the 4 x 2.5-inch HDD backplane . . . . . . . . . . . 124
7.2.8.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 124

Fujitsu PRIMERGY RX100 S8 Specifications

General

Brand	Fujitsu
Model	PRIMERGY RX100 S8
Category	Server
Language	English