Fujitsu PRIMERGY RX100 S8 Upgrade And Maintenance Manual

RX100 S8 Upgrade and Maintenance Manual
Contents
5.2.8 Enabling replaced components in the system BIOS . . . . . . . 79
5.2.9 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 80
5.2.10 Verifying the system time settings . . . . . . . . . . . . . . . . 80
5.2.11 Viewing and clearing the System Event Log (SEL) . . . . . . . 81
5.2.11.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 81
5.2.11.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 82
5.2.12 Updating the NIC configuration file in a Linux environment . . . 83
5.2.13 Enabling BitLocker functionality . . . . . . . . . . . . . . . . . 84
5.2.14 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 85
5.2.15 Looking up changed MAC / WWN addresses . . . . . . . . . . 85
5.2.15.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 85
5.2.15.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 86
5.2.16 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 87
5.2.17 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 88
5.2.17.1 After replacing / upgrading LAN controllers . . . . . . . . . 88
5.2.17.2 After replacing the system board . . . . . . . . . . . . . . . 88
5.2.18 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 89
5.2.19 Performing a fan test after replacing a defective fan . . . . . . 89
6 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 92
6.2 Standard power supply . . . . . . . . . . . . . . . . . . . . 93
6.2.1 Replacing the standard power supply unit . . . . . . . . . . . . 93
6.2.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 93
6.2.1.2 Removing the defective standard power supply unit . . . . . 93
6.2.1.3 Installing the new standard power supply unit . . . . . . . . 95
6.2.1.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 96
6.3 Redundant power supply . . . . . . . . . . . . . . . . . . . 97
6.3.1 Installing a hot-plug power supply unit . . . . . . . . . . . . . . 97
6.3.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 97
6.3.1.2 Removing the dummy cover . . . . . . . . . . . . . . . . . 97
6.3.1.3 Installing a hot-plug power supply unit . . . . . . . . . . . . 98
6.3.1.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 99
6.3.2 Removing a hot-plug power supply unit . . . . . . . . . . . . . 99
6.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 100
6.3.2.2 Removing a hot-plug power supply unit . . . . . . . . . . . 100
6.3.2.3 Installing the dummy cover . . . . . . . . . . . . . . . . . . 101
6.3.3 Replacing a hot-plug power supply unit . . . . . . . . . . . . . 101
6.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 102

Fujitsu PRIMERGY RX100 S8 Specifications

General

Brand	Fujitsu
Model	PRIMERGY RX100 S8
Category	Server
Language	English