83
Program description - Base setup models | Winged models
Note:
•
“Global”, ie specific sender, receiver
bound to respond to the signals of all
model memories “their” station, which is
why firmware version V1101 for safety reasons, a
model change only after switching off the
receiving system is possible.
• “Model” -specific bound receivers respond only
to signals of them explicitly allocated memory
model. One, possibly unintentional, operating
on an unallocated model space is not therefore
possible.
• The HoTT synchronization behavior of a copied
or imported model memory depends on several
factors. For details, refer to the appropriate
section.
• The respective HoTT synchronization type of
“bound” model memory can be seen on the
display of the receiver type in the menu “Model
select”:
“Model” -specific bound receivers are inversely
and “Global”, ie Transmitter far, bound receiver
“normal” displayed.
As an illustration of this, the model memory 01,
02 and 04 with model-specific and model memory
03 are in the figure below exemplified with
transmitter-specific HoTT Syndication:
03
04
Ultimate
02
Starlet
BELL47G
test phase
new to trim
free
free
05
06
01
Graubele
1234g/080811
00:44hE12
00:33hE08
00:22hE08
01:23hE16
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will reset the display to stick
mode "1".
Another tap on the SET key will again deactivate
option selection so a change to another line can be
affected.
Binding type
Note:
This menu item is only visible as long as no
receiver is bound to the currently active
model memory.
An “unbound” model memory can be changed at any
time from the default preset memory specific HoTT
transmitter-specific synchronization, and vice versa.
So If necessary, change the line “Binding Type” and
press the SET button to the right touch pad.
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
1234g/111111
SEL
BD1
BD2
BD3
BD4
Binding type
Model
... And change with the selection keys of the left or
right touch pad, the setting in “global” (or vice versa):
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
1234g/111111
SEL
BD1
BD2
BD3
BD4
Binding type
Global
Module
Model name
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
Graubele
1234g/111111
SEL
BD1
BD2
BD3
BD4
The mc-32 transmitter has a HoTT RF module as
standard equipment. In addition to the built-in mod-
ule, there is a connector for an external RF module
behind one of the two front cover flaps (see page 25)
and a switchover to an external module connected
there can be affected per software. To do this, use the
selection keys of the left or right touch pad to move
the marker frame left to the "Module" selection field
above the "SEL" column label.
HoTT
To be able to connect to the transmitter, Graupner
HoTT receiver must be connected to at least one
model memory “of their” Graupner HoTT transmitter.
This process is commonly referred to by the English
term “binding” and can be repeated anytime. This
“binding” of a receiver is by default always memory-
specic, but may at any time and for any unbound
model memory of a transmitter in the menu that
appears row “binding type”, see above, to transmitter
specic, and can be reversed, changed.
Important notices:
•
During the binding procedure be
sure the transmitter’s antenna is
always far enough away from the
receiver’s antenna.
To Next Page
Loading...
