93
Program description - Base setup models | Helicopter models
This info note will appear as a supplement in the
»Model select« menu and in the sub-menus of the
»Copy / Erase« menu item.
Stick mode
“MODE 2” (Throttle at left stick)
“MODE 3” (Throttle at right stick)
“MODE 4” (Throttle at left stick)
“MODE 1” (Throttle at right stick)
pitch axis
tail rotor
pitch axis
tail rotor
throttle
roll
roll
throttle
tail rotor
tail rotor
throttle throttle
pitch axis
pitch axis
roll
roll
pitch axis
pitch axis
roll
roll
Motor/Pitch
throttle
tail rotor
tail rotor
throttle
throttle
roll
roll
pitch axis
pitch axis
tail rotor
tail rotor
Basically there are four different ways to assign the
four helicopter control functions, roll, nick, tail rotor
and throttle/pitch to the two sticks. Just which of these
is used depends on the preferences of the individual
model pilot.
Use the selection keys of the left or right touch
pad to select the "Stick mode" line. The option field
will be framed.
Model name
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
SEL
Starlet
1234g/111111
Tap on the SET key. The currently displayed stick
mode will be displayed in inverse video. Now use the
selection keys of the right touch pad to select from
among options 1 through 4.
A simultaneous tap on the or keys of the
right touch pad (CLEAR) will reset the display to
stick mode "1".
Another tap on the SET key will again deactivate
option selection so a change to another line can be
affected.
Binding type
Note:
This menu item is only visible as long as no
receiver is bound to the currently active
model memory.
An “unbound” model memory can be changed at any
time from the default preset memory specific HoTT
transmitter-specific synchronization, and vice versa.
So If necessary, change the line “Binding Type” and
press the SET button to the right touch pad.
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
1234g/111111
SEL
BD1
BD2
BD3
BD4
Binding type
Model
... And change with the selection keys of the left or
right touch pad, the setting in “global” (or vice versa):
Stick mode
1
n/a
BASIC SETTING,MODEL
Info
n/a
n/a
Module
bind
HoTT
1234g/111111
SEL
BD1
BD2
BD3
BD4
Binding type
Global
Note:
•
“Global”, ie specific sender, receiver
bound to respond to the signals of all
model memories “their” station, which is
why firmware version V1101 for safety reasons, a
model change only after switching off the
receiving system is possible.
• “Model” -specific bound receivers respond only
to signals of them explicitly allocated memory
model. One, possibly unintentional, operating
on an unallocated model space is not therefore
possible.
• The HoTT synchronization behavior of a copied
or imported model memory depends on several
factors. For details, refer to the appropriate
section.
• The respective HoTT synchronization type of
“bound” model memory can be seen on the
display of the receiver type in the menu “Model
select”:
“Model” -specific bound receivers are inversely
and “Global”, ie Transmitter far, bound receiver
“normal” displayed.
As an illustration of this, the model memory 01,
02 and 04 with model-specific and model memory
03 are in the figure below exemplified with
transmitter-specific HoTT Syndication:
03
04
Ultimate
02
Starlet
BELL47G
test phase
new to trim
free
free
05
06
01
Graubele
1234g/080811
00:44hE12
00:33hE08
00:22hE08
01:23hE16
To Next Page
Loading...
