8
8
8-9
8-9
Service Mode > FAX > List of SSSW
Service Mode > FAX > List of SSSW
FAX
List of SSSW
• FAX model only
FAX>SSSW
SSSW No. Bit No. Function
SW 01 (Errors, COPY functions)
Bit 0 Output error codes for service technicians
Bit 1 Error in memory dump
Bit 2 Enter the password for transferring received condential image
Bit 3 Prohibit COPY
Bit 4 Display No. 300s
Bit 6 Prohibit users from setting date/time
Bit 7 Collectively clear user setting prohibition
SW 02 (Setting for network connection criteria)
Bit 0 Do not start when memory clear list is unable to output
Bit 4 V34 CCRTN OFF
Bit 7 Connect the terminal as F network type 2
SW 03 (Echo measures)
Bit 0 Check EQM of TCF
Bit 1 Apply echo protect tone to V.29
Bit 4 Heard DIS twice
Bit 5 First DIS interference
Bit 6 Interfered DIS frequency
Bit 7 Output 1080Hz before CED
SW 04 (Measures against communication troubles)
Bit 0 Monitor LC
Bit 1 Check CI signal frequency
Bit 2 V21 end ag
Bit 3 Prohibit T.30 node F kept by both parties
Bit 4 T.30 node F echo timer
Bit 5 Check CI signal frequency when setting PBX
Bit 6 Do not send CNG for manual outgoing transmission
Bit 7 Do not send CED for manual incoming transmission
SW 05 (Standard functions, DIS signal setting)
Bit 1 mm/inch conversion (text mode)
Bit 2 mm/inch conversion (text and picture / picture mode)
Bit 3 Prohibit DIS from transmitting bit33 and the followings.
Bit 4 Declare cut sheets
Bit 5 Declare LRT/LGL in DIS
Bit 6 Prohibit ECM outgoing transmission
Bit 7 Prohibit ECM incoming transmission
FAX>SSSW
SSSW No. Bit No. Function
SW 06 (Setting of reading criteria)
Bit 0 Move from DES to pre-scan position
Bit 1 Pre-scan at time other than power-ON
Bit 2 Restrict document length
Bit 3 Stamp option
Bit 4 Reading width 0:A4 1: LTR
Bit 5 Record memory copy time sharing
Bit 6 Variable resolution at COPY
Bit 7 Half tone + super ne
SW 07-SW 11
-
Not in use
SW 12 (Page timer setting)
Bit 0 1 page timeout (outgoing transmission)
Bit 1
Bit 2 1 page timeout (HT transmission)
Bit 3
Bit 4 1 page timeout (incoming transmission)
Bit 5
Bit 7 1 page timeout
SW 13
Bit 0 Prohibit relay broadcasting / transfer while receiving relay / transfer
Bit 1 Response to faulty image while receiving relay / transfer
Bit 2 Convert mm/inch when transmitting received image
SW 14
Bit 0
Bit 1 Standard paper size type
<NADA>COPIER > OPTION > BODY > MODEL-SZ
Bit 2 Convert inch to mm in both main/vertical scanning directions or only in
vertical scanning direction
Bit 3 Convert inch to mm only for OCR transmission
Bit 4 Declare resolution for Inch series
SW 15
Bit 1 Polarity memory timing at dial-in
Bit 2 Receive incoming calls to ND circuit: device circuit
Bit 6 Detect continuous signals when switching F/T
SW 16-SW 17
Not in use
SW 18
Bit 0 Detect carrier disconnection between DCS and TCF
Bit 1 Waiting time for carrier disconnection between DCS and TCF
Bit 2 Prohibit communication control for IP network
SW 19-SW 21
Not in use
To Next Page
Loading...
