Cisco ASR 1001 Hardware Installation Guide

◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50 in./394 mm
to 19.00 in./482.6 mm
•
Cisco ASR 1004 Router:
◦
Chassis height meets EIA-310 rack spacing 4RU (6.95 in./176.53 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50 in./394 mm
to 19.00 in. /482.6 mm
•
Cisco ASR 1006 Router:
◦
Chassis height meets EIA-310 rack spacing 6RU (10.47 in./266 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50/394mm to
19.00/482.6mm
•
Cisco ASR 1013 Router:
◦
Chassis height meets EIA-310 rack spacing 13RU (22.8 in./579.12 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50/394mm to
19.00 in./482.6 mm
◦
Ships with forward rack-mount brackets installed and an extra set in the accessory kit
Floor Loading Considerations
Ensure that the floor under the rack supporting the Cisco 1000 Series Routers is capable of supporting the
combined weight of the rack and all other installed equipment.
To assess the weight of the fully configured Cisco 1000 Series Router respectively, refer to the table in Physical
Characteristics, on page 120 section.
For additional information about floor loading requirements, consult the document GR-63-CORE, Network
Equipment Building System (NEBS) Requirements: Physical Protection .
Cisco ASR 1000 Series Router Hardware Installation Guide
122
Preparing Your Site for Installation
Floor Loading Considerations

Cisco ASR 1001 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	-
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
USB ports quantity	1
Ethernet LAN (RJ-45) ports	4
VPN tunnels quantity	8000
Product color	Gray
Rack capacity	1U
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	250 W
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	8192 MB
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %

Weight and Dimensions

Depth	461.5 mm
Width	439.42 mm
Height	43.43 mm
Weight	11350 g