Cisco ASR 1001 Hardware Installation Guide

Change SummaryDate
Added information about the Cisco ASR 1002-F
Router.
Unless otherwise noted, the Cisco ASR
1002-F Router supports all the
general-purpose routing and security features
of the Cisco ASR 1002 Router and uses the
same internal control and data-plane
architecture as Cisco ASR 1002 Router and
the Cisco ASR 1002-F Router is supported
only by Cisco software release four code.
Note
June 2009
Added information about Cisco ASR1000-RP2 and
how alarms work with the power supply DB-25
connector. In addition, added safety information and
updated the chapter on field-replaceable units (FRUs).
February 2009
Added information about the improved window of
time allotted to replace a power supply. You now
have up to 5 minutes to replace the power supply.
November 2008
Added information about Cisco ASR1000-ESP20 and
Cisco ASR1000-ESP10-N support. Updated eUSB
device graphics and replacement information.
October 2008
Released the first version of this document for the
Cisco ASR 1000 Series Routers.
May 2008
Document Objectives
This publication describes the installation of the Cisco ASR 1000 Series Aggregation Services Routers,
replacement or upgrading of field-replaceable units (FRUs), and troubleshooting of the Cisco ASR 1000
Series Routers hardware. The purpose of this guide is to enable the safe and efficient installation of the Cisco
ASR 1000 Series Aggregation Services Routers.
For information on installation of the Cisco ASR 1001-X Router, and replacement or upgrading of its
field-replaceable units (FRUs), see the Cisco ASR 1001-X Router Hardware Installation Guide at the
following URL: http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001-x/asr1hig.html.
Note
Audience
This publication is primarily designed for the person responsible for installing, maintaining, and troubleshooting
the Cisco ASR 1000 Series Aggregation Services Routers. The users of this guide should:
•
Be familiar with electronic circuitry and wiring practices.
Cisco ASR 1000 Series Router Hardware Installation Guide
xxiii
Preface
Document Objectives

Cisco ASR 1001 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	-
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
USB ports quantity	1
Ethernet LAN (RJ-45) ports	4
VPN tunnels quantity	8000
Product color	Gray
Rack capacity	1U
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	250 W
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	8192 MB
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %

Weight and Dimensions

Depth	461.5 mm
Width	439.42 mm
Height	43.43 mm
Weight	11350 g